DESIGNED & DIMENSIONED
IN MILLIMETERS[INCHES]
FIG 1
PCIEC-XXX-XXXX-XX-XX-X-XX
PCIEC-098-XXXX-EC-EM-X SHOWN
IMPEDANCE
-85: 85 ohm
(LEAVE BLANK FOR 100 ohm)
OVERALL LENGTH: XXXX + "L" REF (SEE TABLE 3)
IDC LENGTH: XXXX+3.17[.125] 1%
No OF POSITIONS
-036: 36 POSITIONS (X1)
-064: 64 POSITIONS (X4)
-098: 98 POSITIONS (X8)
-164: 164 POSITIONS (X16)
3.00 .118
REF
CABLE OPTIONS
RED STRIPE
TO THIS SIDE
-P: EYESPEED-CABLE AND POWER LINES
-A: ACCELERATE CABLE NO POWER
LINES
*
*
LENGTH
-AP: ACCELERATE CABLE AND POWER
LINES
0050 mm MIN.
(SEE NOTE 11)
(LEAVE BLANK FOR EYESPEED CABLE
FIRST END
AND NO POWER LINES)
(SEE TABLE 4)
(SEE NOTE 9)
-EC: EDGE CARD
(SEE TABLE 4)
SECOND END
-EC: PCIE EDGE CARD
"A"
REF
-EM: PCIEC EDGE MOUNT
CONNECTOR
(SEE TABLE 4)
* NOT RELEASED
"B"
REF
LENGTH: XXXX ± 1%
HDRL-11
(SEE NOTE 5)
C1
36.45 1.435 REF
25.40 1.000
REF
ACCELERATE CABLE
EYESPEED CABLE
FOR 85 OHM OPTION
"85" WILL BE SHOWN
IN THIS REGION
8.70 .343
REF
1.57 .062
REF
ENDS OF CABLE TO BE
POTTED WITH UV EPOXY
NOTES:
C
1.
REPRESENTS A CRITICAL DIMENSION.
2. SUB-TTF LENGTH IS EQUAL TO PCIEC LENGTH.
3. ALL ASSEMBLIES TO BE 100% ELECTRICALLY TESTED
FOR SHORTS AND OPENS.
4. ALL ASSEMBLIES TO BE 100% HI-POT TESTED AT 300V.
5. TOP SUB-TTF NOT SHOWN IN THIS VIEW FOR CLARITY; HDRL-11
TO BE CENTERED ON LOWER SUB-TTF AS SHOWN; HDRL-11 IS
TO CONTAIN PART NUMBER, SHOP NUMBER, & DATE CODE.
6. FOR SUB-ASSEMBLY AND FINISHED GOOD PACKAGING
REQUIREMENTS, REFERENCE PACKAGING STANDARD
CO-HD-WI-3033-M.
C2
C3
11.05 .435
REF
ENDS OF CABLE TO BE
POTTED WITH UV EPOXY
7. FOR PRE-TINNING PROCESS INFORMATION ON THE SUB-
PCB'S, SEE TRAVELER SUB-PCIEC-XXX-EC-XX AND SUB-PCIEC-
XXX-EM-XX. FOR -85 OHM OPTION SEE TRAVELER SUB-PCIEC-
XXX-EC-XX-85 AND SUB-PCIEC-XXX-EM-XX-85.
8. KEY CONSUMES 3 PITCHES.
9. NO POWER LINES CREATES A NO CONNECT CONDITION AT
POSITIONS B1, B2, B3, B8, A2, A3, A9 AND A10
10. HOT PLUG DETECT COMMON AND ONLY FIRST AND LAST
USED ON EACH POSITION.
11. CABLE LENGTHS LONGER THAN 1015 MILLIMETERS ARE NOT
SUPPORTED BY S.I. TEST DATA.
12. SIGNAL MAPPING IS ONLY AVAILABLE IN A 1-TO-1
CONFIGURATION. FOR EXAMPLE A1 TO A1, A2 TO A2, ETC.
THIS PRODUCT MANUFACTURED
WITH LEAD-FREE PROCESSING
Pb
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN MILLIMETERS. THIS DOCUMENT CONTAINS INFORMATION
TOLERANCES ARE:
PROPRIETARY NOTE
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
DECIMALS
ANGLES
2
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
.X: 0.3 [.01]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
.XX: 0.13 [.005]
PHONE: 812-944-6733
FAX: 812-948-5047
.XXX: 0.051 [.0020]
e-Mail info@SAMTEC.com
code 55322
MATERIAL:
SHEET SCALE: 2:1
DO NOT SCALE DRAWING
DESCRIPTION:
PCIEC CABLE ASSEMBLY
DWG. NO.
PCIEC-XXX-XXXX-XX-XX-X-XX
BY:
D FRALEY 08/24/2006 SHEET 1 OF 2
F:\DWG\MISC\MKTG\PCIEC-XXX-XXXX-XX-XX-X-XX-MKT.SLDDRW