CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Chip Type, Standard
CF series
Ultra Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
SMD type : Lead free reflow soldering condition at 260°C peak
correspondence.
Adapted to the RoHS directive (2002/95/EC).
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
–55 ~ +105°C
2.5 ~ 25V
6.8 ~ 1500µF
±20% at 120Hz, 20°C
Not more than value of Standard ratings 120Hz, 20°C
at
tan
δ
(
1)
Not more than value of Standard ratings 100kHz, 20°C
at
ESR
Leakage Current ( 2)
Not more than value of Standard ratings. After 2 minute's application of rated voltage. 20°C
Characteristics of Temperature
Impedance Ratio
Z+105°C / Z+20°C
Z–55°C / Z+20°C
1.25
1.25
(100kHz)
Capacitance change
Within ± 20% of initial value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Initial specified value or less
After 2000 hours' application of rated voltage
at 105°C, capacitors meet the specified value
for life characteristics listed at right.
tan δ
Endurance
Damp Heat
(
1)
ESR
Leakage current ( 2)
Capacitance change
Within ± 20% of initial value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Initial specified value or less
After 1000 hours' application of rated voltage
at 60°C 90%RH, capacitors meet the specified value
for life characteristics listed at right.
tan δ
(
1)
ESR
Leakage current ( 2)
To comply with recommended conditions for
reflow soldering. Pre-heating shall be done
at 150 ~ 200°C and for 60 ~ 180 sec.
In the case of peak temp, less than 250°C,
reflow soldering shall be within two times.
In the case of peak temp, less than 260°C,
reflow soldering shall be once.
Capacitance change
Within ± 10% of initial value ( 3)
130% or less of the initial specified value
130% or less of the initial specified value
Initial specified value or less
tan δ
(
1)
ESR
Resistance to
Soldering Heat
Leakage current ( 2)
Measurement for solder temperature profile shall
be made at the capacitor top and the terminal.
Marking
Navy blue print on the case top
1 ESR measurements should be made at a point on the terminal nearest where the terminals protrude through the plastic platform.
2 Conditioning : If there is doubt about the measured result, measurement should be made again after the rated voltage is applied for 120 minutes at the
temperature of 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Type numbering system (Example : 6.3V 150µF)
Dimensions
(mm)
φ10 × 10L
Size
φD
L
φ6.3 × 6L
6.3
φ8 × 7L
8.0
φ10 × 8L
10.0
10.0
Voltage
V
5.9
6.9
7.9
9.9
A
7.3
9.0
11.0
11.0
2.5
e
4
g
6.3
j
10
A
16
C
20
D
25
E
B
6.6
8.3
10.3
10.3
Code
C
6.6
8.3
10.3
10.3
E
2.1
3.2
4.6
4.6
H
0.5 ~ 0.8
0.8 ~ 1.1
0.8 ~ 1.1
0.8 ~ 1.1
Dimension table in next page.
CAT.8100V