5秒后页面跳转
PCA9622 PDF预览

PCA9622

更新时间: 2024-11-12 10:17:03
品牌 Logo 应用领域
恩智浦 - NXP 驱动器
页数 文件大小 规格书
39页 214K
描述
16-bit Fm+ I2C-bus 100 mA 40 V LED driver

PCA9622 数据手册

 浏览型号PCA9622的Datasheet PDF文件第2页浏览型号PCA9622的Datasheet PDF文件第3页浏览型号PCA9622的Datasheet PDF文件第4页浏览型号PCA9622的Datasheet PDF文件第5页浏览型号PCA9622的Datasheet PDF文件第6页浏览型号PCA9622的Datasheet PDF文件第7页 
PCA9622  
16-bit Fm+ I2C-bus 100 mA 40 V LED driver  
Rev. 03 — 31 August 2009  
Product data sheet  
1. General description  
The PCA9622 is an I2C-bus controlled 16-bit LED driver optimized for voltage switch  
dimming and blinking 100 mA Red/Green/Blue/Amber (RGBA) LEDs. Each LED output  
has its own 8-bit resolution (256 steps) fixed frequency individual PWM controller that  
operates at 97 kHz with a duty cycle that is adjustable from 0 % to 99.6 % to allow the  
LED to be set to a specific brightness value. An additional 8-bit resolution (256 steps)  
group PWM controller has both a fixed frequency of 190 Hz and an adjustable frequency  
between 24 Hz to once every 10.73 seconds with a duty cycle that is adjustable from 0 %  
to 99.6 % that is used to either dim or blink all LEDs with the same value.  
Each LED output can be off, on (no PWM control), set at its individual PWM controller  
value or at both individual and group PWM controller values. The PCA9622 operates with  
a supply voltage range of 2.3 V to 5.5 V and the 100 mA open-drain outputs allow  
voltages up to 40 V.  
The PCA9622 is one of the first LED controller devices in a new Fast-mode Plus (Fm+)  
family. Fm+ devices offer higher frequency (up to 1 MHz) and more densely populated bus  
operation (up to 4000 pF).  
The active LOW Output Enable input pin (OE) blinks all the LED outputs and can be used  
to externally PWM the outputs, which is useful when multiple devices need to be dimmed  
or blinked together without using software control.  
Software programmable LED Group and three Sub Call I2C-bus addresses allow all or  
defined groups of PCA9622 devices to respond to a common I2C-bus address, allowing  
for example, all red LEDs to be turned on or off at the same time or marquee chasing  
effect, thus minimizing I2C-bus commands. Seven hardware address pins allow up to  
126 devices on the same bus.  
The Software Reset (SWRST) Call allows the master to perform a reset of the PCA9622  
through the I2C-bus, identical to the Power-On Reset (POR) that initializes the registers to  
their default state causing the outputs to be set HIGH (LED off). This allows an easy and  
quick way to reconfigure all device registers to the same condition.  
The PCA9622, PCA9625 and PCA9635 software is identical and if the PCA9622 on-chip  
100 mA NAND FETs do not provide enough current or voltage to drive the LEDs, then the  
PCA9635 with larger current or higher voltage external drivers can be used.  

与PCA9622相关器件

型号 品牌 获取价格 描述 数据表
PCA9622_12 NXP

获取价格

16-bit Fm I2C-bus 100 mA 40 V LED driver
PCA9622BS NXP

获取价格

16-bit Fm+ I2C-bus 100 mA 40 V LED driver
PCA9622BS,118 NXP

获取价格

暂无描述
PCA9622DR NXP

获取价格

16-bit Fm+ I2C-bus 100 mA 40 V LED driver
PCA9622DR,118 NXP

获取价格

PCA9622 - 16-bit Fm+ I²C-bus 100 mA 40 V LED
PCA9624 NXP

获取价格

8-bit Fm+ I2C-bus 100 mA 40 V LED driver
PCA9624BS NXP

获取价格

8-bit Fm+ I2C-bus 100 mA 40 V LED driver
PCA9624BS,118 NXP

获取价格

PCA9624 - 8-bit Fm+ I²C-bus 100 mA 40 V LED d
PCA9624PW NXP

获取价格

8-bit Fm+ I2C-bus 100 mA 40 V LED driver
PCA9624PW,118 NXP

获取价格

PCA9624 - 8-bit Fm+ I²C-bus 100 mA 40 V LED d