Philips Semiconductors
Product data sheet
Parallel bus to I2C-bus controller
PCA9564
2
release the PCA9564 from the I C-bus since, when ENSIO is reset,
– A data byte has been received while SIO is in the addressed
slave receiver mode
2
the I C-bus status is lost. The AA flag should be used instead (see
description of the AA flag in the following text).
In the following text, it is assumed that ENSIO = “1”.
• STA, THE START FLAG
– “Own slave address” has been received
When SIO is in the addressed slave transmitter mode, state C8H
will be entered after the last serial is transmitted (see Figure 5).
When SI is cleared, enters the not addressed slave receiver mode,
and the SDA line remains at a HIGH level. In state C8H, the AA flag
can be set again for future address recognition.
STA = “1”: When the STA bit is set to enter a master mode, the SIO
2
hardware checks the status of the I C-bus and generates a START
condition if the bus is free. If the bus is not free, then SIO waits for a
STOP condition (which will free the bus) and generates a START
When SIO is in the not addressed slave mode, its own slave
address is ignored. Consequently, no acknowledge is returned, and
a serial interrupt is not requested. Thus, SIO can be temporarily
condition after the minimum buffer time (t
) has elapsed.
BUF
If STA is set while SIO is already in a master mode and one or more
bytes are transmitted or received, SIO transmits a repeated START
condition. STA may be set at any time. STA may also be set when
SIO is an addressed slave.
2
released from the I C-bus while the bus status is monitored. While
SIO is released from the bus, START and STOP conditions are
detected, and serial data is shifted in. Address recognition can be
resumed at any time by setting the AA flag.
STA = “0”: When the STA bit is reset, no START condition or
repeated START condition will be generated.
• THE CLOCK RATE BITS, CR2, CR1, AND CR0
Three bits determine the serial clock frequency when SIO is in
master mode. The various serial rates are shown in Table 1.
• STO, THE STOP FLAG
STO = “1”: When the STO bit is set while SIO is in a master mode, a
2
STOP condition is transmitted to the I C-bus. When the STOP
condition is detected on the bus, the SIO hardware clears the STO
flag.
The clock frequencies only take the HIGH and LOW times into
consideration. The rise and fall time will cause the actual measured
frequency to be lower than expected.
If the STA and STO bits are both set, then a STOP condition is
transmitted to the I C-bus if SIO is in a master mode. SIO then
transmits a START condition.
The frequencies shown in Table 1 are unimportant when SIO is in a
slave mode. In the slave modes, SIO will automatically synchronize
with any clock frequency up to 400 kHz.
2
STO = “0”: When the STO bit is reset, no STOP condition will be
generated.
Table 1. Serial Clock Rates
SERIAL CLOCK FREQUENCY
CR2
CR1
CR0
• SI, THE SERIAL INTERRUPT FLAG
(kHz)
SI = “1”: When the SI flag is set, then, if the ENSIO bit is also set, a
serial interrupt is requested. SI is set by hardware when one of 24 of
the 25 possible SIO states is entered. The only state that does not
cause SI to be set is state F8H, which indicates that no relevant
state information is available.
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
330
288
217
146
1
88
While SI is set, the LOW period of the serial clock on the SCL line is
stretched, and the serial transfer is suspended. A HIGH level on the
SCL line is unaffected by the serial interrupt flag. SI must be reset
by writing “0” to the SI bit. The SI bit cannot be set by the user.
59
44
36
NOTE:
SI = “0”: When the SI flag is reset, no serial interrupt is requested,
and there is no stretching of the serial clock on the SCL line.
1. The clock frequency values are approximate and may vary
with temperature, supply voltage, process, and SCL output
2
loading. If normal mode I C parameters must be strictly followed
• AA, THE ASSERT ACKNOWLEDGE FLAG
AA = “1”: If the AA flag is set, an acknowledge (LOW level to SDA)
will be returned during the acknowledge clock pulse on the SCL line
when:
– The “own slave address” has been received
– A data byte has been received while SIO is in the master receiver
mode
(SCL < 100kHz), it is recommended not to use
CR[2:0] = 100 (SCL = 88kHz) since the clock frequency might be
slightly higher than 100 kHz under certain temperature, voltage,
and process conditions and use CR[2:0] = 101 (SCL = 59 kHz)
instead.
The Status Register, I2CSTA: I2CSTA is an 8-bit read-only register.
The three least significant bits are always zero. The five most
significant bits contain the status code. There are 25 possible status
codes. When I2CSTA contains F8H, no relevant state information is
available and no serial interrupt is requested. All other I2CSTA
values correspond to defined SIO states. When each of these states
is entered, a serial interrupt is requested (SI = “1”).
– A data byte has been received while SIO is in the addressed
slave receiver mode
AA = “0”: if the AA flag is reset, a not acknowledge (HIGH level to
SDA) will be returned during the acknowledge clock pulse on SCL
when:
– A data byte has been received while SIO is in the master receiver
mode
6
2006 Sep 01
5秒后页面跳转
STM32H743技术深度剖析与应用案例探索
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
74HC14芯片资料介绍：性能特性分析、引脚介绍
LM1875芯片手册：功放参数分析、引脚说明、电路设计要点
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
