SMT POWER INDUCTORS
Shielded Drum Core - P1173 Series
Low profile and suitable for compact surface
area mounting
Large permissible DC current
Low DC resistance
Electrical Specifications @ 25°C — Operating Temperature -40°C to +85°C
2
3
Inductance
@Irated
(µH) MIN
Inductance
@0ADC
Saturation
Current
Heating
Current
(A)
1
4
DCR (mΩ)
Part
Number
Irated
(ADC)
Core Loss
Factor K
TYP
MAX
(µH)
@25°C (A)
P1173.132T
P1173.202T
P1173.272T
P1173.372T
P1173.472T
P1173.602T
P1173.762T
P1173.103T
P1173.123T
P1173.153T
P1173.183T
P1173.223T
P1173.273T
P1173.333T
P1173.393T
P1173.473T
P1173.683T
0.8
1.3
1.8
2.4
3.1
3.9
4.9
7.5
9.0
11.3
13.5
16.5
20.3
24.8
29.3
35.3
51.0
14
10
2.3
4.5
5.8
6.8
7.6
13.0
14.3
17.3
23.3
28.3
29.4
33.2
36.2
49.3
65.2
71.4
108.0
3.0
6.0
7.3
8.5
9.5
16.5
18.5
21.8
29.0
35.4
37.0
42.0
45.9
64.8
81.5
89.0
135.0
1.3 30ꢀ
2.0 30ꢀ
2.7 30ꢀ
3.7 30ꢀ
4.7 30ꢀ
6.0 30ꢀ
7.6 30ꢀ
10 20ꢀ
12 20ꢀ
15 20ꢀ
18 20ꢀ
22 20ꢀ
27 20ꢀ
33 20ꢀ
39 20ꢀ
47 20ꢀ
68 20ꢀ
15
13
11
14
10
89.8
113.0
129.1
153.4
171.9
196.3
225.0
248.7
276.3
300.8
339.1
369.7
409.4
455.9
494.8
551.3
671.0
9.0
8.3
7.9
6.0
5.7
5.2
4.5
4.1
4.0
3.8
3.4
3.0
2.7
2.6
2.1
9.0
8.3
7.9
6.0
5.7
5.2
4.5
4.1
4.0
3.8
3.6
3.1
2.7
2.6
2.1
9.2
8.2
6.9
6.2
5.5
5.1
4.4
4.3
3.8
3.4
3.0
2.8
2.6
2.1
Notes from Table
Estimated Temperature Rise:
1. The rated current as listed is either the saturation current
or the heating current depending on which value is lower.
component with 30mm length 28 gauge buss wires and
applying the current to the device for 30 minutes. The tem-
perature is measured by placing the thermocouple between
the winding and the shield.
Trise = [Total loss (mW) / 6.288].833 (oC )
Total loss = Copper loss + Core loss (mW)
Copper loss = Irms2 x DCR (Typical) (mW)
Irms = [IDC2 + ∆I2/12]1/2 (A)
Core loss = 6.81 x 10-7 x f (kHz)1.1 x (K x ∆I)2.15 (mW),
where f varies between 25 kHz and 300 kHZ, and B less
than 2000 Gauss.
2. The saturation current is the current which causes the
inductance to drop to 65ꢀ (or 75ꢀ) of its nominal induc-
tance at zero bias. This current is determined by placing
the component at room ambient (25°C), and applying a
short duration pulse current (to eliminate self-heating
effects) to the component.
4. In high volt*time applications, additional heating in the
component can occur due to core losses in the inductor
which may necessitate derating the current in order to limit
the temperature rise of the component. In order to deter-
mine the approximate total loss (or temperature rise) for a
given application, both copper losses and core losses
should be taken into account.
3. The heating current is the dc current, which causes the
temperature of the part to increase by not more than 40°C.
This current is determined by extending the terminals of the
Schematic
Mechanical
.315
8,00
.315
8,00
.079
2,00
1
2
.118
3,00
2
1
1
2
XXX
.472
12,00
.075
1,91
.315
8,00
.472
12,00
.320
8,13
.630
16,00
.134
3,40
SUGGESTED PAD LAYOUT
.945
24,00
Inches
mm
.010
0,25
Dimensions:
Weight . . . . . . . . 4.5 grams
Tape & Reel. . . . . . 450/reel
Unless otherwise specified, all tolerances are
TAPE & REEL LAYOUT
•
•
•
•
•
•
US 858 674 8100 UK 44 1483 401 700 France 33 3 84 35 04 04 Singapore 65 287 8998 Taiwan 886 2 2698 0228 Hong Kong 852 2788 6588 http://www.pulseeng.com
16
PC500.B (5/02)