Solid Polymer Aluminum Electrolytic Capacitors
NSPVM Series
SUPER LOW ESR, WIDE TEMPERATURE, SURFACE MOUNT, POLARIZED
FEATURES
• ULTRA LOW ESR (TO 13mΩ)
• HIGH RIPPLE CURRENT RATINGS
• REDUCED SIZES (LOW PROFILE)
* NEW *
Low ESR &
High Ripple Current
CHARACTERISTICS
Rated Voltage Range
Capacitance Range
2.5 ~ 35VDC
10 ~ 1,200μF
Operating Temperature Range
Capacitance Tolerance
-55°C ~ +105°C
±20% (M)
2.5V ~ 20V = 0.2CV
25V ~ 35V = 0.5CV
Maximum Leakage Current
After 2 minutes
W.V. (Vdc)
S.V. (Vdc)
Tan δ
2.5
2.9
4.0
4.6
6.3
7.2
10
11.5
0.12 max.
16
18
20
23
25
28.7
35
40
Max. Tan δ at 120Hz/20°C
Z-55°C/Z+20°C
Z+105°C/Z+20°C
Duration
<1.15
<1.25
Low Temperature Stability
Impedance Ratio @ 120Hz
All Case Sizes: 2,000 hours
Δ Capacitance
Δ Tan δ
Within ±20% of initial measured value
Less than 150% of specified value
Less than 150% of specified value
Less than specified value
Load Life Test
@ 105°C
Δ ESR
Δ LC
The following specifications shall be satisfied when the capacitors are restored to +20°C after
subjecting them to the DC rated voltage at +60°C, 90% ~ 95% RH for 500 hours.
Appearance
Δ Capacitance
Δ Tan δ
No significant damage
Within ±20% of initial measured value
Less than 150% of specified value
Less than 150% of specified value
Less than specified value
Damp Heat
Δ ESR
Δ LC
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the specified surge
voltage @ +105°C for 30 seconds through a protective resistor (1K ohm) and discharged for 5 minutes,
30 seconds.
Appearance
Δ Capacitance
Δ Tan δ
No significant damage
Within ±20% of initial measured value
Less than 150% of specified value
Surge Voltage
Failure Rate
Δ ESR
Δ LC
Less than 150% of specified value
Less than specified value
0.5% per 1,000 hours maximum (Confidence level 60% @ +105°C)
PEAK REFLOW SOLDERING CODE
PART NUMBER SYSTEM
Code
Peak Reflow Temperature
NSPVM 391 M 2.5V 6.3X6 L LB F .
L
J
+250°C
+240°C
RoHS Compliant
Sn-Bi Finish, 15" Reel
Peak Reflow Temperature: L = +250°C, J = +240°C
Case Size (DφxL)
Working Voltage (Vdc)
Tolerance Code (M=20%)
TERMINATION/PACKAGING CODE
Code
Termination Finish and Reel Size
Capacitance Code: First 2 characters
significant, third character is multiplier
LB
Sn-Bi Finish, 15" reel
Series
Please review the notes on correct use, safety and precautions found on
pages T10 & T11 of NIC’s Electrolytic Capacitor catalog.
Also found at www.niccomp.com/precautions
If in doubt or uncertainty, please review your specific application - process
details with NIC’s technical support personnel: tpmg@niccomp.com
NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com
1
SPECIFICATIONS ARE SUBJECT TO CHANGE