NuDAM
1
Software &
Utilities
2
DAQ
ND-6058
28-CH PPI Module
ND-6063
8-CH Relay Output Module
3
Programmable I/O
■ꢀ8255 programmable peripheral interface
mode 0 emulation
Relay Output
■ꢀChannels: 8 independent relay outputs
■ꢀOutput Type: 8 form A
PXI
■ꢀContact Rating
•ꢀDC 1 A / 30 V
■ꢀChannel: 24
■ꢀInput Signal
4
•ꢀON/OFF interval time: 3 ms (at 20°C)
■ꢀInternal Insulation
■ꢀResistance:ꢀ1000ꢀMΩꢀ@ꢀ500ꢀVDC
■ꢀExpected Life: 2 x 105
(1 A 30 VDC resistive at 20 cpm)
Power
ꢀ
•ꢀTTL level
■ꢀInternalꢀPull-UpꢀResistor:ꢀ10ꢀkΩ
■ꢀMaximum Current: 0.5 mA
■ꢀOutput Signal
Modular
Instruments
•ꢀTTL level
Digital Input
■ꢀ Requirement: unregulated +10 V to +30 VDC
■ꢀ Power Consumption: 1.416 W typical
5
■ꢀChannels: 4
■ꢀTTL level
Power
GPIB & Bus
Expansion
■ꢀRequirement: unregulated +10 V to +30 VDC
■ꢀPower Consumption:1.488 W typical
Connector
■ꢀ50-pin female SCSI II
6
Motion
Control
ND-6067
8-CH AC Relay Output Module
ND-6060
7
Relay Output & Digital Input Module
Real-time
Distributed
I/O
Relay Output
■ꢀ Channels: 4 relay outputs
Relay Output
■ꢀ Output Type: 2 form C and 2 form A
■ꢀ Contact Rating:
■ꢀChannels: 5 independent relay outputs
and 3 common source replay outputs
■ꢀOutput type: 8 form A
8
ꢀ
•ꢀDC 2A / 30 V
■ꢀ ON/OFF Interval Time: 3 ms
■ꢀ Internal Insulation Resistance:
ꢀꢀꢀꢀꢀ1000ꢀMΩꢀ@ꢀ500ꢀVDC
PAC
■ꢀContact rating:
■ꢀ Expected Life: 2 x105
ꢀ
ꢀ
•ꢀAC 3 A / 250 V
•ꢀDC 3 A / 30 V
(1 A 30 VDC resistive at 20 cpm)
■ꢀ Programmable output polarity
■ꢀ Programmable output power on/safety state
Digital Input
■ꢀ Channels: 4
■ꢀON/OFF time interval: 6 ms/3 ms
9
ꢀ
ꢀ
•ꢀOperate time: approx. 6 ms
•ꢀRelease time: approx. 3 ms
■ꢀ Common External Voltage: +24 V
■ꢀ CurrentꢀLimitꢀResistor:ꢀ2.2ꢀkΩ
■ꢀ Isolation Voltage: 5000 VRMS
■ꢀ Input Type: dry contact
■ꢀ Programmable input polarity
■ꢀInsulationꢀresistance:ꢀ1000ꢀMΩꢀminimum
(at 500 VDC)
■ꢀExpected Life: 2 x 105
(3 A 250 VAC, 3 A 30 VDC at 20 cpm)
Power
■ꢀPower Requirement: +10 V to +30 VDC
Unregulated with against power reversal
■ꢀPower Consumption: 1.392 W typical
Remote I/O
Power
10
■ꢀ Requirement: unregulated +10 V to +30 VDC
■ꢀ Power Consumption: 0.84 W typical
Communi-
cations
11
ND-6080
2-CH Counter/Frequency Input Module
Vision
Counter Inputs
■ꢀProgrammable Digital Noise Filter: 4 μs
to 1.02 ms
■ꢀChannels: Two independent 32-bit counter
■ꢀInput Frequency: 20 KHz max.
■ꢀInput Mode: isolated or non-isolated
■ꢀIsolation Voltage: 5000 VRMS
■ꢀIsolation Input Level
•ꢀLogical level 0: +1 V max
•ꢀLogical level 1: 3.5 V to 30 V
■ꢀCurrentꢀLimitꢀResistor:ꢀ1.2ꢀkΩ
■ꢀNon-isolated Input Level programmable
threshold
■ꢀAlarm: alarm comparator on each counter
Frequency Measurement
12
■ꢀRange: 1 Hz to 20 KHz
■ꢀProgrammable built-in gate time: 1.0 / 0.1 s
Fanless
Embedded
Computers
Digital Output
■ꢀChannels: 2
•ꢀLogical l level 0: 0 V to +5 V
■ꢀOpen collector to 30 V, 30 mA max. load
13
Industrial
Computers
(default = 0.8 V)
Power
ꢀ
•ꢀLogicalꢀlevelꢀ1:ꢀ0ꢀVꢀtoꢀ+5ꢀV
(default = 2.4 V)
■ꢀInput Pulse Width: > 5 μs
■ꢀRequirement: unregulated +10 V to +30 VDC
■ꢀPower Consumption: 2.016 W
cPCI &
■ꢀMax Count: 4,294,967,295 (32-bit)
9-6
www.adlinktech.com