Support &
Community
Product
Folder
Order
Now
Tools &
Software
Technical
Documents
MSP430F6779A, MSP430F6778A, MSP430F6777A, MSP430F6776A, MSP430F6775A
MSP430F6769A, MSP430F6768A, MSP430F6767A, MSP430F6766A, MSP430F6765A
MSP430F6749A, MSP430F6748A, MSP430F6747A, MSP430F6746A, MSP430F6745A
SLAS982A –MAY 2014–REVISED SEPTEMBER 2018
MSP430F677xA, MSP430F676xA, MSP430F674xA Polyphase Metering SoCs
1 Device Overview
1.1 Features
1
• Accuracy < 0.1% Over 2000:1 Dynamic Range for
Phase Current
• Meets or Exceeds ANSI C12.20 and IEC 62053
Standards
• Support for Multiple Sensors Such as Current
Transformers, Rogowski Coils, or Shunts
• Highly Integrated Digital
– Three-Channel Direct Memory Access (DMA)
Controller
– Integrated Hardware AES-128 Module for
Encryption
– 16-Bit Cyclic Redundancy Check (CRC) Module
• Power Measurement for up to Three Phases Plus
Neutral
– Four 16-Bit Timers With Nine Total
Capture/Compare Registers
• Dedicated Pulse Output Pins for Active and
Reactive Energy for Calibration
• Six Enhanced Universal Serial Communication
Interfaces (eUSCIs)
• 4-Quadrant Measurement per Phase or
Cumulative
• Exact Phase-Angle Measurements
• Digital Phase Correction for Current Transformers
• Temperature-Compensated Energy Measurements
– eUSCI_A0, eUSCI_A1, eUSCI_A2, and
eUSCI_A3 Support UART, IrDA, and SPI
– eUSCI_B0, eUSCI_B1 Support SPI and I2C
• Ultra-Low Power Consumption
– Multiple Low-Power Modes
• 40-Hz to 70-Hz Line Frequency Range Using
Single Calibration
– Standby Mode (LPM3): 2.1 µA at 3 V,
Wake up in Less Than 5 µs
• Flexible Power Supply Options With Automatic
Switching
• Display Operates at Very Low Power During AC
Mains Failure: 3 µA in LPM3
• LCD Driver With Contrast Control for up to 320
Segments
• Password-Protected Real-Time Clock (RTC) With
Tamper Detection, Crystal Offset Calibration, and
Temperature Compensation
– RTC Mode (LPM3.5): 0.34 µA at 3 V
– Shutdown Mode (LPM4.5): 0.18 µA at 3 V
• CPU
– High-Performance 25-MHz CPU With 32-Bit
Multiplier
– Wide Input Supply Voltage Range:
3.6 V Down to 1.8 V
• Memory
– Up to 512KB of Single-Cycle Flash
– Up to 32KB of RAM With Single-Cycle Access
• Package Options
– 128-Pin LQFP (PEU) Package With 90 I/O Pins
– 100-Pin LQFP (PZ) Package With 62 I/O Pins
• Development Tools (Also See Tools and Software)
• Integrated Security Modules to Support
Anti‑Tamper and Encryption
• Multiple Communication Interfaces for Smart Meter
Implementations
• High-Performance Analog
– Up to Seven Independent 24-Bit Sigma-Delta
ADCs With Differential Inputs and Variable Gain
– 10-Bit 200-ksps SAR ADC With Six External
Channels and Two Internal Channels, Including
Supply and Temperature Sensor Measurement
– Energy Measurement Design Center for
MSP430 MCUs with 24-Bit Sigma-Delta ADCs
(MSP-EM-DESIGN-CENTER)
– Three-Phase Electronic Watt-Hour EVM for
Metering (EVM430-F6779)
– Target Development Board
(MSP‑TS430PEU128)
1.2 Applications
•
•
3-Phase Electronic Watt-Hour Meters
Utility Metering
•
Energy Monitoring
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.