RESISTORS wCAPS&COILS wDELAY LINES
ECONOMICAL 1 WATT TO 3 WATT
POWER FILM MELF RESISTORS
MPF SERIES
FEATURES
RCD’s MPF Series utilize special filming processes and
r High power in small body size
r Low cost MELF design
r Wide resistance range: 0.1Ω to 10MΩ
r Standard tolerance: ±5% (available to ±0.5%)
r Inherent low inductance film performance
highest grade materials to achieve high power density, yet
the economical MELF package enables pricing well below
rectangular counterparts. The multilayer coating offers
excellent environmental protection and dielectric strength,
and is resistant to industrial solvents, steam and humidity.
OPTIONS
r Option P - Increased Pulse Capability
r Option 37 - Group A Screening per Mil-R-39008
r Numerous design modifications are avaialble (special marking,
matched sets, etc). Consult factory for application assistance
L
D
W
Inch [mm]
SPECIFICATIONS
RCD
Type
Wattage Voltage
Resistance
Range2
L
D
W (Min.)
Rating
Rating1
300V
350V
350V
400V
400V
MPF1
MPF2S
MPF2
MPF3S
MPF3
1W
0.1Ω to 1MΩ
0.1Ω to 4.7MΩ
0.1Ω to 4.7MΩ
0.1Ω to 6.8MΩ
0.1Ω to 10MΩ
.232±.008 [5.9±.2]
.335±.012 [8.5±.3]
.413±.012 [10.5±.3]
.413±.012 [10.5±.3]
.575±.012 [14.6±.3]
.087±.008 [2.2±.2]
.118±.008 [3 ± .2]
.158±.012 [4 ± .3]
.158±.012 [4 ± .3]
.189±.012 [4.8±.3]
.036 [.9]
.047 [1.2]
.056 [1.4]
.056 [1.4]
.064 [1.6]
2W
2W
3W
3W
Not to exceed (PxR), increased working voltages available. 2 Extended range available
1
√
TYPICAL PERFORMANCE CHARACTERISTICS
PULSE CAPABILITY
10000
Temperature Coefficient
200ppm/°C ≤1M,
350ppm 1M-6.8M,
500ppm >6.8M)
1000
100
10
Operating Temperature
-55 to +165°C
MPF1, 2, 3 Power Derating:
MPF2S, 3S Power Derating:
1.053%/°C >70°C
.714%/°C >25°C
Dielectric Strength
Insulation Resistance
Solderabilty
500V
MPF3P
MPF2P, 3SP
MPF2SP
MPF1P
10,000Meg ohm
95% Min.
1uS
10uS
100uS
1mS
10mS
100mS
Short Time Overload (2.5xW 5S, not
to exceed 2x volt rating)
0.5% MPF1,2,3;
1% MPF2S, 3S
Pulse Duration
Pulse capability is dependent on res. value, waveform, repetition rate,
current, etc. Chart is a general guide for Opt. P pulse resistant version,
single pulse, with peak voltage levels not exceeding 1KV MPF1, 1.5KV
MPF2S, 2KV MPF2, 2.5KV MPF3S, 3KV MPF3. Max pulse capability for
standard parts (w/o Opt.P) is 50% less. For improved performance and
reliability, a 30-50% pulse derating factor is recommended (or larger for
frequent pulses, high values, etc). Consult RCD for application assistance.
Verify selection by evaluating under worst-case conditions. Increased
pulse levels available.
Voltage Coefficient
25ppm/V
0.3%
1%
Resistance to Solder Heat (245°C,5S)
Temperature Cycling
Moisture Resistance
2%
Load Life (1000 hours at rated W)
2% MPF1,2,3;
4% MPF2S, 3S
P/N DESIGNATION:
APPLICATION NOTE
MPF2S
- 1002 - J
T
The temp. rise of SM resistors depends largely on heat conduction
through the end terminations, which can vary significantly depending
on PCB material and layout (i.e. pad size, trace area, copper thickness,
air convection, etc.). Typical temperature rise at full rated power is
100°C for MPF1,2,3 and 150°C for MPF2S & 3S (based on DIN44050
PCB material with 500 sq. mil circuit traces MPF1, 2, 2S and 1000 sq.
mil MPF3,3S). It is recommended to evaluate product in actual use
conditions to ensure the proper component and PCB layout is utilized.
RCD Type
Options: P, 37 (leave blank if standard)
4-Digit Resis. Code: 3 signif. digits & multiplier.
R100=0.1Ω, 1R00=1Ω, 10R0=10Ω ,1000=100Ω, 1001=1K
Tolerance : J= 5% (std), D=0.5%, F=1%, G=2%, K=10%
Packaging : B = Bulk, T = Tape & Reel
RCD Components Inc., 520 E. Industrial Park Dr., Manchester, NH USA 03109
Tel: (603) 669-0054 Fax:(603) 669-5455 E-mail: sales@rcdcomponents.com www.rcdcomponents.com
FA026B Specifications subject to change without notice