DESIGNED & DIMENSIONED
IN MILLIMETERS[INCHES]
REVISION W
FIG 2
MHXXX-XXXXX-XXXXXX-XXXX
CABLE STRIPPING DIMENSIONS
PER CONFIGURATIONS
OVERALL CABLE LENGTH
MILLIMETERS OF CABLE
0030 MIN. (SEE NOTE 8, 9 & 18)
CABLE CALLOUT
081: CCA-081
(0.81 OD MINIATURE COAX CABLE)
113: CCA-113
(1.13 OD MINIATURE COAX CABLE)
DO NOT
SCALE FROM
THIS PRINT
(SEE TABLE 1)(SEE NOTES 12,13,14,15)
"A" mm
"B" mm
"C" mm
C
END 2 CONNECTOR OR PREPARATION
-MH1RP: MHF1-P-C-X-RA-CAX (SEE SHEET 2)
(081 CABLE TYPE: MHF1-P-C-X-RA-CA3)
(113 CABLE TYPE: MHF1-P-C-X-RA-CA4)
-MH3RP: MHF3-P-C-X-RA-CA3 (SEE SHEET 2)
(081 CABLE TYPE ONLY)
END 1 CONNECTOR
-MH1RP: MHF1-P-C-X-RA-CAX (SEE SHEET 2)
(081 CABLE TYPE: MHF1-P-C-X-RA-CA3)
(113 CABLE TYPE: MHF1-P-C-X-RA-CA4)
-MH3RP: MHF3-P-C-X-RA-CA3 (SEE SHEET 2)
(081 CABLE TYPE ONLY)
-01BJ1: SMA-J-C-X-ST-BHX (SEE SHEET 2)
(081 CABLE TYPE: SMA-J-C-X-ST-BH3)
(113 CABLE TYPE: SMA-J-C-X-ST-BH4)
-01BJ2: SMA-J-C-X-ST-BRX (SEE SHEET 2)
(081 CABLE TYPE: SMA-J-C-X-ST-BR3)
(113 CABLE TYPE: SMA-J-C-X-ST-BR4)
-01SB1: SMA-J-C-X-ST-SBX (SEE SHEET 2)
(081 CABLE TYPE: SMA-J-C-X-ST-SB3)
(113 CABLE TYPE: SMA-J-C-X-ST-SB4)
-01SR1: SMA-J-C-X-ST-SRX (SEE SHEET 2)
(081 CABLE TYPE: SMA-J-C-X-ST-SR3)
(113 CABLE TYPE: SMA-J-C-X-ST-SR4)
-SING: SINGLE ENDED (ONE END ONLY, SEE NOTE 11)
-XXXXXX: STRIPPED AND TINNED (THIS END ONLY-
SEE NOTES 11-15, 17, 19 & SHEET 2, FIG 3)
"D" mm
"E" mm
C
C
-01BJ1: SMA-J-C-X-ST-BHX (SEE SHEET 2)
(081 CABLE TYPE: SMA-J-C-X-ST-BH3)
(113 CABLE TYPE: SMA-J-C-X-ST-BH4)
-01BJ2: SMA-J-C-X-ST-BRX (SEE SHEET 2)
(081 CABLE TYPE: SMA-J-C-X-ST-BR3)
(113 CABLE TYPE: SMA-J-C-X-ST-BR4)
-01SB1: SMA-J-C-X-ST-SBX (SEE SHEET 2)
(081 CABLE TYPE: SMA-J-C-X-ST-SB3)
(113 CABLE TYPE: SMA-J-C-X-ST-SB4)
-01SR1: SMA-J-C-X-ST-SRX (SEE SHEET 2)
(081 CABLE TYPE: SMA-J-C-X-ST-SR3)
(113 CABLE TYPE: SMA-J-C-X-ST-SR4)
(SEE FIG 2) "C" FORMAT: X.Xmm
(SEE FIG 2) "B" FORMAT: X.Xmm
(SEE FIG 2) "A" FORMAT: X.Xmm
DO NOT LEAVE ANY SPACE BLANK,
EACH POSITION MUST CONTAIN A
NUMERIC CHARACTER 0 THRU 9.
NOTES:
C
C
1.
REPRESENTS A CRITICAL DIMENSION.
LENGTH: XXXX
2. CABLE CUT LENGTH:
(SEE TABLE 2 FOR TOLERANCE)
(SEE NOTE 2 FOR CABLE CUT LENGTH)
= (LENGTH: XXXX) - (SUBTRACTOR FOR END 1) - (SUBTRACTOR FOR END 2).
(SEE TABLE 1 FOR SUBTRACTORS)
3. ASSEMBLY TO BE 100% TESTED FOR OPENS & SHORTS.
4. ASSEMBLY TO BE 100% HI-POT TESTED PER TABLE 1, THE TEST VOLTAGE FOR THE ASSEMBLY
SHOULD BE SET TO THE END OPTION WITH THE LOWEST TEST VOLTAGE RATING.
C
ATTACH LABEL-ET
THIS END
C 5. AFTER FINAL ELECTRICAL TESTS, LABEL EACH CABLE ASSEMBLY WITH 1 LABEL -ET.
FOR LENGTHS UNDER 100MM, LABEL EACH CABLE WITH DOT MARK.
6. CRITICALS ON CONNECTOR PRINTS TO BE CHECKED IN PROCESS.
7. FINISHED ASSEMBLIES TO BE PACKAGED PER PACKAGING STANDARD CO-RF-WI-3040-M.
ASSEMBLIES WITH LOCKWASHERS, NUTS, AND GASKETS TO BE SHIPPED KITTED AS ONE
ASSEMBLY PER BAG, UNASSEMBLED.
END 1
8. CABLE STOCKED IN INCHES, 1 INCH = 25.4 MILLIMETERS.
9. CABLE LENGTHS LONGER THAN 1000 MILLIMETERS ARE NOT SUPPORTED BY S.I. TEST DATA.
10. MINIMUM BEND RADIUS FOR MH081 = 5.0 [.20]
END 2
MH113 = 6.8 [.27]
FIG 1
11. FOR SING ENDED OR STRIPPED AND TINNED ASSEMBLIES: MAKE A DOUBLE ENDED
ASSEMBLY AT TWICE THE CABLE LENGTH AND TEST BEFORE CUTTING ASSEMBLY IN HALF.
12. DIM "A", "B", AND "C" HAVE A MINIMUM VALUE OF 0.0mm & A MAXIMUM VALUE OF 9.9mm.
13. PRODUCTION OF STRIP AND TIN FOR CENTER DIELECTIC USE: A.
14. PRODUCTION OF STRIP AND TIN FOR SHIELD USE: D=A+B.
15. PRODUCTION OF STRIP AND TIN FOR JACKET USE: E=A+B+C.
16. FOR -RA TO -RA, CONNECTORS SHOULD BOTH BE ORIENTED UP. (SEE SHEET 2, FIG. 4)
17. FOR STRIPPED AND TINNED OPTION, ONLY THE CENTER CONDUCTOR IS TINNED.
18. IF NO MHXXX OPTION IS LISTED FOR EITHER END, MINIMUM LENGTH IS 100MM.
19. JACKET SLUG IS LEFT PARTIALLY INSERTED OVER SHIELD TO PREVENT DAMAGE
DURING SHIPPING.
MHXXX-MH1RP-01BJ1-XXXX SHOWN
THIS PRODUCT MANUFACTURED
WITH LEAD-FREE PROCESSING
Pb
F:\DWG\MISC\MKTG\MHXXX-XXXXX-XXXXXX-XXXX-MKT.SLDDRW
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS CONFIDENTIAL AND
PROPRIETARY INFORMATION AND ALL DESIGN,
MANUFACTURING, REPRODUCTION, USE, PATENT RIGHTS
AND SALES RIGHTS ARE EXPRESSLY RESERVED BY SAMTEC,
INC. THIS DOCUMENT SHALL NOT BE DISCLOSED, IN WHOLE
OR PART, TO ANY UNAUTHORIZED PERSON OR ENTITY NOR
REPRODUCED, TRANSFERRED OR INCORPORATED IN ANY
OTHER PROJECT IN ANY MANNER WITHOUT THE EXPRESS
WRITTEN CONSENT OF SAMTEC, INC.
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN
*
*
MILLIMETERS [INCHES].
TOLERANCES ARE:
DECIMALS
ANGLES
2
.X: 0.3 [.01]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
.XX: 0.13 [.005]
PHONE: 812-944-6733
FAX: 812-948-5047
code 55322
.XXX: 0.051 [.0020]
e-Mail info@SAMTEC.com
MATERIAL:
SHEET SCALE: 2:1
DO NOT SCALE DRAWING
DESCRIPTION:
SEE END 1 AND END 2 ASSEMBLY PRINTS
MICRO RF CABLE ASSEMBLY
NO.
DWMG. HXXX-XXXXX-XXXXXX-XXXX
07/26/2005
CUMMINGS
SHEET 1 OF
3
BY:
5秒后页面跳转
英伟达新AI芯片Rubin或提前半年亮相
苹果iPhone 17将全系采用三星/LG显示LTPO OLED面板
三星深化印度制造布局，供应链本地化进程加速
芯擎科技“星辰一号”自动驾驶芯片点亮成功，2025年量产在即
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
