1.2 x 45 (2 PLCS)
REVISION E
SEE NOTE 10
2.00
DESIGNED & DIMENSIONED
IN MILLIMETERS
SEE NOTE 2
"D"
MECT-XX-01-D-RAX
TAIL OPTION
1.24
No OF POSITIONS (PER ROW)
-RA1: STANDARD
-10, -15, -20, -35
(SEE FIG. 1)
-RA2: ELEVATED
(SEE FIG. 2)
*
FIG. 1
MECT-35-01-D-RA1 SHOWN
'B'
BODY STYLE
-01: 1mm(.039) PCB
2.10
SEE NOTE 11
"D"
ROW SPECIFICATION
-D: DOUBLE ROW
(No OF POS x 0.80) + 3.00
C1
(No OF POS x 0.800) + 1.400
(SEE NOTE 6)
* = NOT TOOLED
0.90 x 45 (TYP)
0.350 X 45° (TYP)
0.210
0.50
0.900
0.80
7.400
6.25
4.20
2.30
C2
R0.45
(No OF POS -1) x 0.800
"B"
1.20±0.03
"A"
C
L
"C"
30°
5.10 REF
1.300±0.08
1.05
4.900
2.350
C5
1.49
"C"
SEE TABLE 1
"A"
'C'
1.15
(2 PLCS)
"B"
E
1.10
C4
'H'
0.40
0.70
0.200
R0.50
((No OF POS -1) x 0.800) 0.05
(TOL NON-ACCUM)
0.40
(2 PLCS)
'A'
0.400
C3
0.36
0.15
0.80
C6
30°
(No OF POS + 2) x 0.800
SECTION "A"-"A"
SCALE 4 : 1
SECTION "B"-"B"
SCALE 4 : 1
(No OF POS x 0.80) + 0.24
POS 2
NOTES:
POS 1
2.30
'F'
C
1.
REPRESENTS A CRITICAL DIMENSION.
C
L
2. SAMTEC LOGO SHALL APPEAR AT LOCATION ON SURFACE SHOWN,
APPROXIMATELY 3.81 x 3.18.
1.400
3. ALL MULTIPLE CAVITY MOLDS SHALL IDENTIFY EACH CAVITY WITH A NUMBER
DESIGNATION LOCATED WHERE SHOWN.
2.400
2.000
2.20
4. ALL IDENTIFICATION MARKS MUST NOT STAND GREATER THAN 0.05mm OFF THE
SURFACE OF THE PART.
E
SECTION "C"-"C"
5. MOLDED SURFACES SHALL BE CONSISTENT AND SMOOTH. SURFACES TO BE
FREE OF SCATCHES, NICKS, SINK AREAS, VOIDS OR OTHER BLEMISHES.
6. MEASURE SLOT LENGTH AT BOTTOM OF SLOT; DRAFT ON ALL SIDES OF SLOT
MUST BE WITHIN TOLERANCES.
CAVITY ID
(SEE NOTES 3, 4, & 13)
'G'
'D'
1.38 (TYP)
3.45
7. MAXIMUM BOW: SEE TABLE 1.
C7
E
8. ALL DRAFT MUST BE WITHIN SPECIFIED TOLERANCES.
9. ALL DIMENSIONS SYMMETRICAL ABOUT CENTERLINE WITHIN 0.025 UNLESS
OTHERWISE SPECIFIED.
((No OF POS -1) x 0.800) 0.05
(TOL NON-ACCUM)
0.40 (TYP)
1.75 (TYP)
1.350
(2 PLCS)
3.45
10. GATE PAD TO BE RECESSED 0.13mm.
C
L
11. POSITION 1 INDICATOR TO BE RECESSED 0.10mm.
12. MOLD IS CAPABLE OF PRODUCING 30, 40 & 50 POSITIONS.
13. ALL BODIES REQUIRE A + IDENTIFIER TO INDICATE SFP+ COMPATABILITY
SECTION "D"-"D"
E
E 14. -35 POSITION TO BE MADE FROM VECTRA V143XL
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN MILLIMETERS.
PROPRIETARY NOTE
0.40
(TYP)
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
0.70
'E'
TOLERANCES ARE:
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DECIMALS
ANGLES
2
0.90
.X: .3
.XX: .08
.XXX: .051
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
SHEET SCALE: 2:1
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
C8
.8mm MINI-EDGE CARD, TRANSCEIVER RECEPTACLE
VECTRA E130i OR VECTRA V143XL, COLOR: BLACK
MAX REGRIND: 50%
E
NO.
DWG. MECT-XX-01-D-RAX
MAX FLASH ALLOWED: .08
MAX GATE VESTIGE: .08
KEVIN B
10/9/2001
SHEET 1 OF 2
BY:
F:\DWG\MISC\MKTG\MECT-XX-01-D-RAX-MKT.SLDDRW