19-3864; Rev 3; 10/06
High-Performance, Single-Ended, Current-Mode
PWM Controllers
General Description
Features
The MAX5094A/B/C/D/MAX5095A/B/C BiCMOS, high-
performance, current-mode PWM controllers have all the
features required for wide input-voltage range
isolated/nonisolated power supplies. These controllers
are used for low- and high-power universal input volt-
age and telecom power supplies.
♦ Pin-for-Pin Replacement for UCC28C43
(MAX5094A) and UCC28C45 (MAX5094B)
♦ 2A Drive Source and 1A Sink Capability
♦ Up to 1MHz Switching Frequency Operation
♦ Bidirectional Frequency Synchronization
(MAX5095A/MAX5095B)
The MAX5094/MAX5095 contain a fast comparator with
only 60ns typical delay from current sense to the output
for overcurrent protection. The MAX5094 has an inte-
grated error amplifier with the output at COMP. Soft-
start is achieved by controlling the COMP voltage rise
using external components.
♦ Advanced Output Drive for Secondary-Side
Synchronous Rectification (MAX5095C)
♦ Fast 60ns Cycle-by-Cycle Current Limit
♦ Trimmed Oscillator Capacitor Discharge Current
Sets Maximum Duty Cycle Accurately
The oscillator frequency is adjustable from 20kHz to
1MHz with an external resistor and capacitor. The tim-
ing capacitor discharge current is trimmed allowing for
programmable dead time and maximum duty cycle for
a given frequency. The available saw-toothed waveform
♦ Accurate 5ꢀ Start ꢁoltage with 0ꢂ8ꢁ Hysteresis
♦ Low 32µA Startup Current
♦ 5ꢁ Regulator Output (REF) with 20mA Capability
♦ ꢁersions with 0ꢂ3ꢁ Current-Sense Threshold
♦ Overtemperature Shutdown
at R C can be used for slope compensation when
T
T
needed.
The MAX5095A/MAX5095B include a bidirectional syn-
chronization circuit allowing for multiple controllers to
run at the same frequency to avoid beat frequencies.
Synchronization is accomplished by simply connecting
the SYNC of all devices together. When synchronizing
with other devices, the MAX5095A/MAX5095B with the
highest frequency synchronizes the other devices.
Alternatively, the MAX5095A/MAX5095B can be syn-
chronized to an external clock with an open-drain out-
put stage running at a higher frequency.
Ordering Information
PIN-
PKG
PART
TEMP RANGE
PACKAGE CODE
MAX5094AASA
MAX5094AASA+
MAX5094AAUA*
MAX5094AAUA+
MAX5094BASA*
MAX5094BASA+
MAX5094BAUA*
MAX5094BAUA+
-40°C to +125°C 8 SO
-40°C to +125°C 8 SO
-40°C to +125°C 8 µMAX
-40°C to +125°C 8 µMAX
-40°C to +125°C 8 SO
-40°C to +125°C 8 SO
-40°C to +125°C 8 µMAX
-40°C to +125°C 8 µMAX
S8-4
S8-4
U8-1
U8-1
S8-4
S8-4
U8-1
U8-1
The MAX5095C provides a clock output pulse
(ADV_CLK) that leads the driver output (OUT) by
110ns. The advanced clock signal is used to drive the
secondary-side synchronous rectifiers.
The MAX5094A/B/C are available in the 8-pin SO and
+Denotes lead-free package.
*Future product—contact factory for availability.
Ordering Information continued at end of data sheet.
®
8-pin µMAX
packages. The MAX5094D and
MAX5095A/B/C are available in the 8-pin µMAX pack-
age. All devices operate over the automotive tempera-
ture range of -40°C to +125°C.
Pin Configurations
Applications
TOP VIEW
Universal Input AC/DC Power Supplies
Isolated Telecom Power Supplies
Isolated Power-Supply Modules
Networking Systems
COMP
FB
1
2
3
4
8
7
6
5
REF
V
CC
MAX5094
CS
OUT
GND
Computer Systems/Servers
Industrial Power Conversion
Isolated Keep-Alive Circuits
R /C
T
T
µMAX/SO
Pin Configurations continued at end of data sheet.
µMAX is a registered trademark of Maxim Integrated Products, Inc.
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.