Evaluate: MAX40000
MAX40001
MAX40000/MAX40001
Evaluation Kits
Procedure
General Description
The MAX40000/MAX40001 EV kits are fully assembled
and tested. Follow steps below to verify board operation.
Caution: Do not turn on the power supply until all
connections are completed. By default, the MAX40000
EV kit comes with the MAX40000ANT12+.
The MAX40000 and MAX40001 evaluation kits (EV kits)
are fully assembled and tested PC boards that evaluate
the MAX40000 and MAX40001 single comparators with
internal voltage references, respectively. By default, the
MAX40001 EV kit has an open-drain output, while the
MAX40000 EV kit has a push-pull output. These EV
kits come with a MAX40000ANT12+/MAX40001ANT12+
1) Connect the positive terminal of a DC power supply
to the VDD test point and the ground terminal to the
GND test point.
2) Connect the positive terminal of a DC power supply to
the VPULL test point and the ground terminal to the
GND test point (not applicable for the MAX40000
EV kit). This is not necessary while evaluating the
MAX40000 on the MAX40001 EV kit. R3 needs to be
removed while using MAX40001 EV kit to evaluate
the MAX40000 push-pull version.
installed that operate off a V
supply between 1.7V and
CC
5.5V, an internal reference voltage of 1.252V, and have a
wide -0.2V to +5.7V input voltage (V ) range. These EV kits
IN
demonstrate the MAX40000ANT12+/MAX40001ANT12+
in an ultra-small, 1.1mm x 0.76mm, 6-bump wafer-level
package (WLP) with 0.35mm bump spacing.
These EV kits can be used to evaluate the entire family
of MAX40000/MAX40001 with 6-bump WLP options.
Remove pullup resistor R3 on the MAX40001 EV kit
when evaluating the MAX40000 in place of the default
MAX40001 IC included in the MAX40001 EV kit.
3) Connect the positive terminal of a DC power supply
to the INP test point and the ground terminal to the
GND test point.
4) Use a wire to short INM test point and V
test point
REF
to connect voltage reference output (1.252V, default)
to inverting input.
Features
● -0.2V to V
+ 0.2 Input Voltage Range
DD
5) Turn on the V
power supply and set it to any voltage
CC
● 1.7V to 5.5V V
Range with Internal Reference
DD
between 1.7V to 5.5V.
• 1.252V, 1.66V, 1.94V, and 2.22V Internal Voltage
6) Monitor the output voltage at the VREF test point
using DMM. This should be 1.252V (default) when either
the MAX40000ANT12+/MAX40001ANT12+ is used.
Reference Options Available (V
the Voltage Reference Option)
min Depends on
DD
Note: Refer to the Electrical Characteristics table of the
MAX40000 IC data sheet for more information on minimum V
7) Turn on the V
power supply and set it to any voltage
PULL
.
DD
between 1.7V to 5.5V (MAX40001 only). Do not need
V
supply when MAX40000 (push-pull output) is
● Configured to Add External Hysteresis
● Evaluates 6-Bump WLP
PULL
used on the MAX40001 EV kit.
8) Turn on the INP power supply and set it to the desired
level.
9) Monitor the output using a DMM at the VOUT test point
and study its response to varying voltage at INP. Ideally,
voltage at the VOUT test point of the MAX40001 EV kit
● Proven PCB Layout
● Fully Assembled and Tested
Quick Start
Required Equipment
should be at logic-high (V ) when voltage applied on
PULL
INP is greater than 1.252V and should be at logic-low
(0V) when voltage applied on INP is less than 1.252V.
10) While, on the MAX40000 EV kit, the voltage on the
Before beginning, the following equipment is needed:
●
●
Three +5V DC power supplies (V , INP, and V
DD
on MAX40001EVKIT)
PULL
VOUT test point will be at V
when the voltage on INP
CC
Two digital multimeters (DMMs)
is greater than 1.252V, it should be at GND when the
voltage applied on INP is less than 1.252.
Ordering Information appears at end of data sheet.
19-8620; Rev 2; 6/17
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
