MAX3223
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
SLLS409A – MARCH 2000
DB, DGV, DW, OR PW PACKAGE
Meets or Exceeds the Requirements of
TIA/EIA-232-F and ITU v.28 Standards
(TOP VIEW)
Operates With 3-V to 5.5-V V
Operates up to 250 kbit/s
Supply
CC
EN
C1+
V+
C1–
C2+
FORCEOFF
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
V
CC
GND
DOUT1
RIN1
ROUT1
FORCEON
Low Standby Current . . . 1 µA Typical
External Capacitors . . . 4 × 0.1 µF
Accepts 5-V Logic Input With 3.3-V Supply
C2–
V–
Designed to Be Interchangeable With
Maxim MAX3223
DOUT2
RIN2
ROUT2
13 DIN1
12 DIN2
RS-232 Bus-Pin ESD Protection Exceeds
±15-kV Using Human-Body Model (HBM)
11
INVALID
Applications
– Battery-Powered Systems, PDAs,
Notebooks, Laptops, Palmtop PCs, and
Hand-Held Equipment
Package Options Include Plastic
Small-Outline (DW), Shrink Small-Outline
(DB), Thin Very Small-Outline (DGV), and
Thin Shrink Small-Outline (PW) Packages
description
The MAX3223device consists of two line drivers, two line receivers, and a dual charge-pump circuit with ±15-kV
ESD protection pin to pin (serial-port connection pins, including GND). The device meets the requirements of
TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and
the serial-port connector. The charge pump and four small external capacitors allow operation from a single
3-V to 5.5-V supply. The devices operate at data signaling rates up to 250 kbit/s and a maximum of 30-V/µs
driver output slew rate.
Flexible control options for power management are available when the serial port is inactive. The
auto-powerdown feature functions when FORCEON is low and FORCEOFF is high. During this mode of
operation, if the device does not sense a valid RS-232 signal, the driver outputs are disabled. If FORCEOFF
is set low and EN is high, both drivers and receivers are shut off, and the supply current is reduced to 1 µA.
Disconnecting the serial port or turning off the peripheral drivers causes the auto-powerdown to occur.
Auto-powerdown can be disabled when FORCEON and FORCEOFF are high. With auto-powerdown enabled,
the device is activated automatically when a valid signal is applied to any receiver input. The INVALID output
is used to notify the user if an RS-232 signal is present at any receiver input. INVALID is high (valid data) if any
receiver input voltage is greater than 2.7 V or less than –2.7 V or has been between –0.3 V and 0.3 V for less
than 30 µs. INVALID is low (invalid data) if the receiver input voltage is between –0.3 V and 0.3 V for more than
30 µs. Refer to Figure 4 for receiver input levels.
The MAX3223C is characterized for operation from 0°C to 70°C. The MAX3223I is characterized for operation
from –40°C to 85°C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2000, Texas Instruments Incorporated
PRODUCT PREVIEW information concerns products in the formative or
design phase of development. Characteristic data and other
specifications are design goals. Texas Instruments reserves the right to
change or discontinue these products without notice.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265