19-0529; Rev 1; 9/06
10-Bit, 45Msps, Full-Duplex
Analog Front-End
MAX9713
General Description
Features
♦ Dual 10-Bit, 45Msps Rx ADC and Dual 10-Bit,
The MAX19713 is an ultra-low-power, highly integrated
mixed-signal analog front-end (AFE) ideal for wideband
communication applications operating in full-duplex (FD)
mode. Optimized for high dynamic performance and
ultra-low power, the device integrates a dual 10-bit,
45Msps receive (Rx) ADC; dual 10-bit, 45Msps transmit
(Tx) DAC; three fast-settling 12-bit aux-DAC channels for
ancillary RF front-end control; and a 10-bit, 333ksps
housekeeping aux-ADC. The typical operating power in
FD mode is 91.8mW at a 45MHz clock frequency.
45Msps Tx DAC
♦ Ultra-Low Power
91.8mW at fCLK = 45MHz, FD Mode
79.2mW at fCLK = 45MHz, Slow Rx Mode
49.5mW at fCLK = 45MHz, Slow Tx Mode
Low-Current Standby and Shutdown Modes
♦ Programmable Tx DAC Common-Mode DC Level
and I/Q Offset Trim
♦ Excellent Dynamic Performance
The Rx ADCs feature 54dB SINAD and 72.2dBc SFDR at
5.5MHz input frequency with a 45MHz clock frequency.
The analog I/Q input amplifiers are fully differential and
full-scale signals. Typical I/Q channel
matching is 0.03 phase and 0.02dB gain.
SNR = 54.1dB at fIN = 5.5MHz (Rx ADC)
SFDR = 70.3dBc at fOUT = 2.2MHz (Tx DAC)
accept 1.024V
P-P
♦ Three 12-Bit, 1µs Aux-DACs
The Tx DACs feature 70.3dBc SFDR at f
= 2.2MHz
♦ 10-Bit, 333ksps Aux-ADC with 4:1 Input Mux and
OUT
and f
= 45MHz. The analog I/Q full-scale output volt-
CLK
Data Averaging
age range is 400mV differential. The output DC com-
mon-mode voltage is selectable from 0.71V to 1.06V. The
I/Q channel offset is adjustable to optimize radio lineup
sideband/carrier suppression. Typical I/Q channel
matching is 0.01dB gain and 0.05ꢀ phase.
♦ Excellent Gain/Phase Match
0.03° Phase, 0.02dB Gain (Rx ADC) at
fIN = 5.5MHz
♦ Multiplexed Parallel Digital I/O
Two independent 10-bit parallel, high-speed digital
buses used by the Rx ADC and Tx DAC allow full-
duplex operation for frequency-division duplex applica-
tions. The Rx ADC and Tx DAC can be disabled
independently to optimize power management. A 3-wire
serial interface controls power-management modes, the
aux-DAC channels, and the aux-ADC channels.
♦ Serial-Interface Control
♦ Versatile Power-Control Circuits
Shutdown, Standby, Idle, Tx/Rx Disable
♦ Miniature 56-Pin Thin QFN Package
(7mm x 7mm x 0.8mm)
The MAX19713 operates on a single 2.7V to 3.3V analog
supply and 1.8V to 3.3V digital I/O supply. The
MAX19713 is specified for the extended (-40ꢀC to
+85ꢀC) temperature range and is available in a 56-pin,
thin QFN package. The Selector Guide at the end of the
data sheet lists other pin-compatible versions in this AFE
family. For time-division duplex (TDD) applications, refer
to the MAX19705–MAX19708 AFE family of products.
Pin Configuration
TOP VIEW
42 41 40 39 38 37 36 35 34 33 32 31 30 29
28
27
26
25
ADC1 43
DAC3 44
DAC2 45
DAC1 46
DA3
DA2
DA1
DA0
V
47
24 OV
DD
DD
Applications
IDN 48
IDP 49
GND 50
23 OGND
22 AD9
WiMAX CPEs
Portable Communication
Equipment
MAX19713
21
AD8
V
51
20 AD7
19 AD6
18 AD5
17 AD4
16 AD3
15 AD2
DD
801.11a/b/g WLAN
VoIP Terminals
QDN 52
QDP 53
REFIN 54
COM 55
REFN 56
EXPOSED PADDLE (GND)
Ordering Information
1
2
3
4
5
6
7
8
9
10 11 12 13 14
PART*
PIN-PACKAGE
56 Thin QFN-EP**
56 Thin QFN-EP**
PKG CODE
T5677-1
THIN QFN
NOTE: THE PIN 1 INDICATOR IS “+” FOR LEAD-FREE DEVICES.
MAX19713ETN
MAX19713ETN+
T5677-1
Functional Diagram and Selector Guide appear at end of
data sheet.
*All devices are specified over the -40ꢀC to +85ꢀC operating range.
**EP = Exposed paddle. +Denotes lead-free package.
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.