5秒后页面跳转
MAX17222EVKIT PDF预览

MAX17222EVKIT

更新时间: 2024-11-08 02:51:03
品牌 Logo 应用领域
美信 - MAXIM /
页数 文件大小 规格书
7页 484K
描述
400mV to 5.5V Input Range

MAX17222EVKIT 数据手册

 浏览型号MAX17222EVKIT的Datasheet PDF文件第2页浏览型号MAX17222EVKIT的Datasheet PDF文件第3页浏览型号MAX17222EVKIT的Datasheet PDF文件第4页浏览型号MAX17222EVKIT的Datasheet PDF文件第5页浏览型号MAX17222EVKIT的Datasheet PDF文件第6页浏览型号MAX17222EVKIT的Datasheet PDF文件第7页 
Evaluates: MAX17220–MAX17225  
MAX17222 Evaluation Kit  
General Description  
Quick Start  
The MAX17222 evaluation kit (EV kit) evaluates the  
MAX17220–MAX17225 IC family of ultra-low quiescent  
current step-up DC-DC converters. The MAX17222 EV  
kit features two independent circuits to evaluate two  
different IC packages of the MAX17220–MAX17225  
family. Both circuits on the EV kit operate over an input  
range of 400mV to 5.5V, depending on load, with 0.88V  
typical startup with 3kΩ load. Each circuit provides  
resistor-configurable output voltages from 1.8V to 5V in  
100mV/step.  
Required Equipment  
MAX17222 EV kit  
1.8V to 5V, 3A DC power supply  
Electronic load capable of 225mA  
Digital voltmeter (DVM)  
Procedure  
The EV kit is fully assembled and tested. Follow the steps  
below to verify board operation.  
Caution: Do not turn on power supply until all  
connections are completed.  
The EV kit comes with the MAX17222ELT+ and  
MAX17222ENT+ installed.  
Testing the 3V Output Circuit  
Features  
1) Verify that jumper JU101 is in its default position, as  
shown in Table 2.  
2) Connect the power supply between the IN and nearest  
GND terminal posts.  
Two Independent Circuits on One Board  
• Evaluates the MAX17220–MAX17225 IC Family in  
a 6-pin µDFN  
3) Connect the electronic load between the 3V output  
and nearest GND terminal posts.  
• Evaluates the MAX17220–MAX17225 IC Family in  
a 6-pin Wafer-Level Package (WLP)  
4) Connect the DVM between the 3V output and nearest  
GND terminal posts.  
5) Set the input power supply to 1.8V and turn on the  
power supply.  
● 400mV to 5.5V Input Range  
● 1.8V to 5V Configurable Output Voltage in  
100mV/step  
6) Set the electronic load to 225mA and enable the  
electronic load.  
7) Verify that the voltage at the 3V terminal post is  
approximately 3V.  
● Up to 100mA/225mA/425mA Output Current  
Proven 2-Layer 1oz Copper PCB Layout  
Demonstrates Compact Solution Size  
● Fully Assemble and Tested  
Testing the 5V Output Circuit  
1) Verify that jumper JU1 is in its default position, as  
shown in Table 1.  
MAX17222 EV Kit Files  
2) Connect the power supply between the IN1 and  
nearest GND1 terminal posts.  
3) Connect the electronic load between the 5V output  
and nearest GND1 terminal posts.  
4) Connect the DVM between the 5V output and a  
nearest GND1 terminal posts.  
FILE  
DESCRIPTION  
MAX17222 EV BOM  
EV Kit Bill of Material  
MAX17222 EV PCB Layout  
EV Kit Layout  
EV Kit Schematic  
Diagrams  
MAX17222 EV Schematic  
5) Set the input power supply to 3V, and turn on the  
power supply.  
6) Set the electronic load to 225mA, and enable the  
electronic load.  
MAX17222 EV Minimal  
Component Schematic  
Minimal Component Circuit  
7) Verify that the voltage at the 5V terminal post is  
approximately 5V.  
Ordering Information appears at end of data sheet.  
19-8762; Rev 5; 9/20  

与MAX17222EVKIT相关器件

型号 品牌 获取价格 描述 数据表
MAX17223 MAXIM

获取价格

400mV to 5.5V Input, nanoPower Synchronous Boost Converter with True Shutdown
MAX17223 ADI

获取价格

400mV至5.5V输入、nanoPower同步升压转换器,带真关断
MAX17223ELT MAXIM

获取价格

400mV to 5.5V Input, nanoPower Synchronous Boost Converter with True Shutdown
MAX17223ELT+ MAXIM

获取价格

Switching Regulator,
MAX17223ENT MAXIM

获取价格

400mV to 5.5V Input, nanoPower Synchronous Boost Converter with True Shutdown
MAX17223ENT+ MAXIM

获取价格

Switching Regulator,
MAX17223ENT+T MAXIM

获取价格

Switching Regulator,
MAX17224 MAXIM

获取价格

400mV to 5.5V Input, nanoPower Synchronous Boost Converter with True Shutdown
MAX17224 ADI

获取价格

400mV至5.5V输入、nanoPower同步升压转换器,带真关断
MAX17224ELT MAXIM

获取价格

400mV to 5.5V Input, nanoPower Synchronous Boost Converter with True Shutdown