Communication Line – MAB06 Series
3 W 2 : 1 S I N G L E
&
D U A L O U T P U T D C / D C C O N V E R T E R
Specifications
INPUT
Input voltage range
5V
4.5-6V
9-18V
18-36V
36-72V
10VDC max
25VDC max
50VDC max
100VDC max
45-9V
12V
24V
48V
5V
12V
24V
48V
Pi type.
Input surge voltage
(100ms max)
Input filter
OUTPUT
Voltage accuracy
Voltage balance (dual)
2.0ꢀ max.
1.0ꢀ max.
Temperature coefficient 0.05ꢀ%/C.
Ripple and noise 20MHz BW 3.3V%5V
12V%15V
100mV p-p max.
1ꢀ p-p max.
Features
Short circuit protection Continuous.
1
Line regulation
Load regulation
Single%Dual
Single2
Dual3
0.5ꢀ max.
0.5ꢀ max.
1.0ꢀ max.
•ꢀ 3Wꢀisolatedꢀoutput
•ꢀ 24-pinꢀDIPꢀpackage
•ꢀ Efficiencyꢀtoꢀ87%
•ꢀ 2:1ꢀinputꢀrange
ENVIRONMENTAL
Operating ambient temp.–25 to +71/C. “-E” models –40 to +85/C.
Power derating curve
Derating above 71/C
See figure 1.
•ꢀ Regulatedꢀoutputs
Linearly to zero power at 95/C (plastic case).
Linearly to zero power at 100/C (copper case).
95/C% 100/C max (plastic%copper case).
Natural convection.
•ꢀ Piꢀinputꢀfilter
Case temperature4
Cooling
•ꢀ Continuousꢀshortꢀcircuitꢀprotection
•ꢀ MeetꢀEMIꢀEN55022ꢀclassꢀAꢀ(“-E”ꢀmodel)
•ꢀ Noꢀtantalumꢀcapacitorꢀinsideꢀ(“-E”ꢀmodel)
•ꢀ Wideꢀoperatingꢀtemperatureꢀrangeꢀ(“-E”ꢀmodel)
Storage temperature
Humidity
–40 to +100/C.
95ꢀ RH max non-condensing.
GENERAL
Efficiency
See table.
•ꢀ UL60950-1ꢀapprovalꢀforꢀH/HMꢀversionsꢀonlyꢀ
ꢀ andꢀ“-E”ꢀmodel
Isolation voltage
Standard models: 500VDC min.
Suffix “H” models: 3kVDCmin. (non-
conductive black plastic only)
Suffix “HM” models: 1.5kVDC min.
10 ohms.
250pF typ.
100KHz, min.
MIL-STD-217F, 2000Khrs typ.
“-E” models 2500Khrs typ.
®
US
9
E176177
Isolation resistance
Isolation capacitance
Switching frequency
MTBF
Dimensions
DIP
SMD
31.8 x 20.3 x 10.2 mm.
31.8 x 20.3 x 11.4 mm.
S%HS models6 31.8 x 20.3 x 10.4 mm.
Case material
Standard
“M” models
Non-conductive black plastic.
Black coated copper with non-
conductive base
Note:
1. Measured from high line to low line.
2. Measured from full load to 10% load.
3. Measured from full load to 1/4 load.
4. Maximum case temperature under any operating condition should not exceed
95 (Plastic Case), 100 (Copper Case).
5. The output noise is measured with 0.1uF MLCC across for SMD package
6. S and HS models for “E” Version Only
“S” models
12.5g.
SMD package
Weight
Case material
Standard models: Non-conductive black plastic.
5
Suffix “M” models: Black coated copper with
non-conductive base.
20120306
C O M M U N I C A T I O N L I N E
w w w . p o w e r b o x . i n f o