Document 1053
For TI TPS23756
Flyback Transformer 15 W PoE Converter
• Flyback for Texas Instruments TPS23756 Wide Input Range
15 W PoE Converter; shown on PMP6659 schematic and BOM
• Input: 10.8 – 57 V
• 1500 Vrms, one minute isolation from primary and bias to
secondary
Core material Ferrite
Terminations RoHS tin-silver (96.5/3.5) over tin over nickel over
phos bronze. Other terminations available at additional cost.
Weight 11.3 g
Ambient temperature –40°C to +125°C
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 175 per 13″ reel Plastic tape: 44 mm wide,
0.4 mm thick, 28 mm pocket spacing, 11.9 mm pocket depth
PCB washing Tested with pure water or alcohol only. For other solvents,
see Doc787_PCB_Washing.pdf.
L at0A2 LatIpk3
DCR max (Ohms)4
sec bias drive max (µH) pri:sec pri:bias pri:drive
0.060 0.058 0.370 0.323 0.550 1 : 0.57 1 : 0.57 1 : 0.52
Turns ratio6
Part
10ꢀ
(µH)
min
Leakage L5
Ipk3
number1
(µH)
pri
(A)
Output7
MA5281-BL_ 45
40.5
2.8
12 V, 1.25 A
1. When ordering, please specify a packaging code:
MA5281-BLD
4. DCR for the primary and the secondary is measured with windings
connected in parallel.
5. Leakage inductance is for the primary, measured with the windings
connected in parallel and the secondary windings shorted.
6. Turns ratio is with the primary windings and secondary windings con-
nected in parallel.
7. Output is with the secondary windings connected in parallel. Output of the
drive winding is 11 V, 15 mA. Output of the bias winding is 11.5 V, 15 mA.
8. Electrical specifications at 25°C.
Packaging: D = 13″ machine ready reel. EIA-481 embossed plastic
tape (175 parts per full reel).
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter D instead.
2. Inductance is measured at 250 kHz, 0.1 Vrms, 0 Adc.
3. Peak primary current drawn at minimum input voltage.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Dot indicates pin 1
1
12
11
3
4
12
1
12
0.118
3,00
0.028
0,70
Pri
Sec
0.810
20,57
Recommended
Land Pattern
max
0.050
1,27
0.118
3,00
9
10
6
5
8
1
Bias
2
0.930
23,62
0.130
3,3
0.827
21,0
Drive
7
Primary windings and secondary
windings to be connected in parallel
on PC board
0.425
10,80
max
0.004 / 0,10
0.969
24,6
inches
mm
1.181
Dimensions are in
max
30,00
Document 1053 Revised 05/01/13
US +1-847-639-6400 sales@coilcraft.com
UK +44-1236-730595 sales@coilcraft-europe.com
Taiwan +886-2-2264 3646 sales@coilcraft.com.tw
China +86-21-6218 8074 sales@coilcraft.com.cn
Singapore + 65-6484 8412 sales@coilcraft.com.sg
© Coilcraft Inc. 2014
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.