MODEL: M2SES2
F: 0 – 10 mA DC (Load resistance 1500 Ω max.)
Super-mini Signal Conditioners Mini-M Series
G: 0 – 1 mA DC (Load resistance 15 kΩ max.)
Z: Specify current (See OUTPUT SPECIFICATIONS)
Voltage
HIGH/LOW SELECTOR
(with simple loop test output)
1: 0 – 10 mV DC (Load resistance 10 kΩ min.)
2: 0 – 100 mV DC (Load resistance 100 kΩ min.)
3: 0 – 1 V DC (Load resistance 1000 Ω min.)
4: 0 – 10 V DC (Load resistance 10 kΩ min.)
5: 0 – 5 V DC (Load resistance 5000 Ω min.)
6: 1 – 5 V DC (Load resistance 5000 Ω min.)
4W: -10 – +10 V DC (Load resistance 10 kΩ min.)
5W: -5 – +5 V DC (Load resistance 5000 Ω min.)
0: Specify voltage (See OUTPUT SPECIFICATIONS)
Functions & Features
• Monitors two DC input signals and transmitting an output
signal proportional to the higher or lower input
• Simple loop test output (0, 50, 100 %)
• High-density mounting
Typical Applications
• Selecting greater flow, pressure, etc. for control
• Heating control by multiple T/C’s on a furnace
[3] POWER INPUT
23 (.91)
AC Power
M: 85 – 264 V AC (Operational voltage range 85 – 264 V,
47 – 66 Hz)
Model
76
(2.99)
STAT
STAT
2
1
(Select ‘/N’ for ‘Standards & Approvals’ code.)
M2: 100 – 240 V AC (Operational voltage range 85 – 264 V,
47 – 66 Hz)
ZERO
INP2
SPAN
ZERO
INP1
SPAN
124
(4.88)
DC Power
R: 24 V DC
mm (inch)
(Operational voltage range 24 V ±10 %, ripple 10 %p-p max.)
R2: 11 – 27 V DC
MODEL: M2SES2–[1][2]–[3][4]
(Operational voltage range 11 – 27 V, ripple 10 %p-p max.)
(Select ‘/N’ for ‘Standards & Approvals’ code.)
P: 110 V DC
ORDERING INFORMATION
• Code number: M2SES2-[1][2]-[3][4]
Specify a code from below for each of [1] through [4].
(e.g. M2SES2-AA-M2/CE/Q)
(Operational voltage range 85 – 150 V, ripple 10 %p-p max.)
[4] OPTIONS (multiple selections)
Standards & Approvals (must be specified)
/N: Without CE or UL
• Special output range (For codes Z & 0)
• Specify the specification for option code /Q
(e.g. /C01/S01)
/CE: CE marking
Other Options
blank: none
[1] INPUT
Current
/Q: Option other than the above (specify the specification)
A: 4 – 20 mA DC (Input resistance 250 Ω)
B: 2 – 10 mA DC (Input resistance 500 Ω)
C: 1 – 5 mA DC (Input resistance 1000 Ω)
H: 10 – 50 mA DC (Input resistance 100 Ω)
Voltage
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
/C01: Silicone coating
/C02: Polyurethane coating
6: 1 – 5 V DC (Input resistance 1 MΩ min.)
/C03: Rubber coating
TERMINAL SCREW MATERIAL
/S01: Stainless steel
[2] OUTPUT
Current
A: 4 – 20 mA DC (Load resistance 750 Ω max.)
B: 2 – 10 mA DC (Load resistance 1500 Ω max.)
C: 1 – 5 mA DC (Load resistance 3000 Ω max.)
D: 0 – 20 mA DC (Load resistance 750 Ω max.)
E: 0 – 16 mA DC (Load resistance 900 Ω max.)
M2SES2 SPECIFICATIONS
ES-5098 Rev.6 Page 1/3
http://www.m-system.co.jp/