Pl tronics, Inc.
.
19013 36th Ave. W, Suite H Lynnwood, WA 98036 USA
Manufacturer of High Quality Frequency Control Products
LV1145B LVDS Series
Low Voltage Differential Signal Output with Enable/Disable
–
1.50 MHz
650.00 MHz
6 Pad Leadless Surface Mount Oscillator
Consult factory for higher frequencies
Standard Specifications
Overall Frequency Stability
± 50 PPM, ± 25 PPM and ± 20 PPM over Operating Temp. Range
Operating Temperature Range 0 to +80°C is standard, can be extended to - 40 to +85°C
Operable Supply Voltage (Vcc) 3.3 V ± 5% standard, 5.0 V ± 10% also available
High Level Output Voltage
Low Level Output Voltage
Differential Output Voltage
Offset Voltage
Output Leakage Current
Supply Current (Icc) Enabled
1.43 V typical and 1.60 V maximum with output enabled (100 ohm load) See Test circuit #6
0.90 V minimum and 1.10 V typical with output enabled (100 ohm load) See TC #6
247 V minimum, 330 V typical and 454 V maximum with output enabled (100 ohm load) See TC #6
1.125 V minimum, 1.25 V typical and 1.375 V maximum with output enabled (100 ohm load) See TC #6
10 uA maximum with output disabled
50 mA max < 200 MHz, 60 mA max < 500 MHz, 70 mA max 500 MHz and above
Supply Current (Icc) Disabled 20 mA max < 200 MHz, 30 mA max < 500 MHz, 40 mA max 500 MHz and above
Symmetry (DC)
Rise and Fall Time (Tr & Tf)
RMS Jitter
45/55% measured at 0°C <= Ta <= 70°C, 40/60% measured at Ta < 0°C and Ta > 70°C
1.0 nS max at 20% to 80% output swing (100 ohm load) See Test circuit #6 and Waveform #2
1.0 pS max at12 kHz to 20 MHz from the output
Enable / Disable Pin:
The Enable / Disable pin has an internal pull up and if the pin is not connected the oscilaltor is enabled. Pletronics strongly recommends
connecting the Enable / Disable pin to Vcc, if the oscillator is to be enabled at all times. In the disable condition, the output becomes a
high impedance.
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
Output Enable Time
0.7 Vcc minimum at Enable / Disable Pin
0.3 Vcc maximum at Enable / Disable Pin
-20 uA maximum at Enable / Disable Pin = 0.7 Vcc
-200 uA maximum at Enable / Disable Pin = 0 V
200 nS maximum
Output Disable Time
200 nS maximum
Part Numbering Guide
Portions of the part number that appear after the frequency may not be marked on part (C of C provided)
LV11 45 B V - 70.0M - XXX (Internal Code or blank)
Packaging
Tube or
24mm tape
16mm pitch
Model
Frequency in MHz
LV11 = E/D Pin 2
LV33 = E/D Pin 1 & 2
LV37 = E/D Pin 1
Special Specifications (choose all that apply)
E: Extended Operating Temp Range (-40 to +85°C)
V: Supply Voltage of 3.3 volts ±5%
Frequency Stability
Y: Supply Voltage of 5.0 volts ±10%,
45 = ± 50 PPM
44 = ± 25 PPM
20 = ± 20 PPM
Consult factory for available frequencies and specs. Not all options available for all frequencies. A special part number may be assigned.
Frequency Stability is inclusive of frequency shifts due to calibration, temperature, supply voltage, shock, vibration and load
Jun 2004
(425) 776 -1880, Fax: (425) 776-2760, ple-sales@pletronics.com, www.pletronics.com
5
Pl tronics, Inc.