LTC1852/LTC1853
The ● denotes the specifications which apply over the full operating temperature
TIMING CHARACTERISTICS
range, otherwise specifications are at TA = 25°C. (Note 5)
SYMBOL
PARAMETER
CONDITIONS
(Note 10)
MIN
50
10
10
50
50
10
TYP
MAX
UNITS
ns
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
CONVST High Time
Latch Setup Time
●
●
●
●
●
●
13
(Note 10)
ns
14
15
16
Latch Hold Time
(Notes 9, 10)
(Note 10)
ns
WR Low Time
ns
WR High Time
(Note 10)
ns
17
18
19
20
21
22
M1 to M0 Setup Time
M0 to BUSY Delay
M0 to WR (or RD) Setup Time
M0 High Pulse Width
RD High Time Between Readback Reads
Last WR (or RD) to M0
M0 to RD Setup Time
M0 to CONVST
(Notes 9, 10)
M1 High
ns
20
ns
(Notes 9, 10)
(Note 10)
●
●
●
●
●
●
t
ns
19
50
50
10
ns
(Note 10)
ns
(Note 10)
ns
23
(Notes 9, 10)
(Note 10)
t
t
ns
24
25
26
27
19
19
ns
Aperture Delay
–0.5
2
ns
Aperture Jitter
ps
RMS
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: All voltage values are with respect to ground with OGND and GND
wired together unless otherwise noted.
straight line passing through the actual end points of the transfer curve.
The deviation is measured from the center of the quantization band.
Note 8: Bipolar offset is the offset voltage measured from –0.5LSB when
the output code flickers between 1111 1111 1111 and 0000 0000 0000.
For the LTC1853 and between 11 1111 1111 and 00 0000 0000 for the
LTC1852.
Note 3: When these pin voltages are taken below ground or above V
,
Note 9: Guaranteed by design, not subject to test.
Note 10: Recommended operating conditions.
Note 11: The falling CONVST edge starts a conversion. If CONVST returns
high at a critical point during the conversion it can create small errors.
For the best results, ensure that CONVST returns high either within 400ns
after the start of the conversion or after BUSY rises.
DD
they will be clamped by internal diodes. This product can handle input
currents of 100mA below ground or above V without latchup.
DD
Note 4: When these pin voltages are taken below ground, they will be
clamped by internal diodes. This product can handle input currents of
100mA below ground without latchup. These pins are not clamped to V
.
DD
Note 5: V = 5V, f
= 400kHz, t = t = 2ns unless otherwise
DD
SAMPLE
r f
Note 12: The analog input range is determined by the voltage on
REFCOMP. The gain error specification is tested with an external 4.096V
but is valid for any value of REFCOMP greater than 2V and less than
specified.
Note 6: Linearity, offset and full-scale specifications apply for a single-
ended input on any channel with COM grounded.
(V – 0.5V.)
DD
Note 7: Integral nonlinearity is defined as the deviation of a code from a
Note 13: MUX address is updated immediately after BUSY falls.
TYPICAL PERFORMANCE CHARACTERISTICS
8192 Point FFT with
fIN = 39.599kHz
Differential Linearity
0
–20
1.0
0.5
0
–40
–60
–80
–0.5
–1.0
–100
–120
0
200
0
4096
FREQUENCY (kHz)
CODE
1852 F03
1852 F02
18523fa
6