LMT78_1.0R series
Wide input, non-isolated & regulated, single output, SMD package
Switching Regulator
Efficiency up to 95%
No need for heat sinks
1.0AMP SMD package
Wide input voltage range
(4.75V - 32V)
Remote ON/OFF control
Short circuit protection (SCP),
thermal shutdown
Very low shutdown current
Super low ripple and noise
IEC62368, UL62368, EN62368
approved
The LMT78_1.0R series with high efficiency switching regulators is an
ideally supply for space constrained mobile applications. There is no
need for any heat sink, even if operated at + 85°C. The additional
features include remote ON/OFF control and adjustable output
voltage.
Super low ripple and noise of typically only 10mV and a shutdown input
current of typically only 15uA.
Adjustable output voltage
UL-62368-1 (E347551)
Common specifications
Cooling:
Output specifications
Free air convection
Item
Test conditions
Min
Typ
Max
Units
Short circuit protection mode:
Short circuit protection:
Operating temperature range:
Storage temperature range:
Lead temperature:
Hiccup mode
Output voltage
accuracy
Input voltage range at
full load
Continuous, automatic recovery
-40°C ~ +85°C
• 1.5/1.8/2.5/3.3VDC
• Others
2
2
4
3
%
%
Line regulation
Load regulation
Input voltage range at
full load
0.2
0.4
%
-55°C ~ +125°C
300°C MAX, 1.5mm from case for 10 sec
100°C MAX
Nominal input, 10% to
100% load
• 1.5/1.8/2.5VDC
• Others
Operating case temperature:
Reflow Soldering Temperature:
0.8
0.3
1.5
0.6
%
%
Peak temp. ≤ 245°C,maximum duration
time ≤ 60s at 217°C. For actual
application, please refer to
Ripple + Noise*
20MHz bandwidth
1.5/1.8/2.5/3.3VDC
• 20% - 100% load
• < 20% load
Others
• 10% - 100% load
• < 10% load
IPC/JEDEC J-STD-020D.1
30
30
75
75
mVp-p
mVp-p
Storage humidity range:
Case material:
< 95%
Plastic [UL94-V0]
> 2,000,000 hours
1.7g
30
30
75
75
mVp-p
mVp-p
MTBF (MIL-HDBK-217F,+25°C):
Package weight:
Temperature
coefficient
- 40°C to + 85°C
ambient
0.03
%/°C
Dimensions:
15.24 * 11.40 * 8.25mm
Transient response Nominal input voltage,
deviation 25% load step change
50
150
1
mV
Input specifications
Transient recovery Nominal input voltage,
0.2
ms
time
25% load step change
Item
Test conditions
Min Typ
0.2
Max
1.5
Units
mA
Vadj
input voltage range
10
%Vo
No load input
current
Switching
frequency
Full load, nominal
input voltage
• 1.5/1.8/2.5VDC
• 3.3/5/6.5VDC
• 09/12VDC
Reverse polarity
input
Avoid /
370
520
700
KHz
KHz
KHz
Not protected
Input filter
Capacitor
Capacitance filter
Remote ON/OFF*
• Module switch on
• Module switch off
suspended or connected to TTL
high level (3.2-5.5VDC)
* Ripple and noise tested with “parallel cable” method, please refer to DC-DC
pin connected to GND or low
level (0-0.8VDC)
Example:
LMT78_05-1.0R
• Input current when
switched off
0.2
1
mA
LM = Series; T = SMT case; 05 = 5Vout; 1.0 = 1.0A; R = Revised
* The voltage of Remote ON/OFF pin is relative to pin GND.
Note:
1. All specifications measured at Ta = 25°C, humidity <75%, nominal input voltage
and rated output load unless otherwise specified.
2. In this datasheet, all the test methods of indications are based on corporate
standards.
Page 1 of 5
LMT78_1.0R – Rev. 2020-1.3
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com