5. Cleaning
Precautions
◆Cleaning conditions
1. When PCBs are cleaned after capacitors mounting, please select the appropriate cleaning solution in accordance with the intended use
of the cleaning. （e.g. to remove soldering flux or other materials from the production process.）
2. Cleaning condition shall be determined after it is verified by using actual cleaning machine that the cleaning process does not affect
capacitor's characteristics.
1. The use of inappropriate cleaning solutions can cause foreign substances such as flux residue to adhere to capacitors or deteriorate
their outer coating, resulting in a degradation of the capacitor's electrical properties （especially insulation resistance）.
2. Inappropriate cleaning conditions（ insufficient or excessive cleaning） may adversely affect the performance of the capacitors.
In the case of ultrasonic cleaning, too much power output can cause excessive vibration of PCBs which may lead to the cracking of
capacitors or the soldered portion, or decrease the terminal electrodes' strength. Therefore, the following conditions shall be carefully
checked;
Technical
considerations
Ultrasonic output :
20 W/ℓ or les
Ultrasonic frequency :
40 kHz or less
Ultrasonic washing period : 5 min. or less
6. Resin coating and mold
1. With some type of resins, decomposition gas or chemical reaction vapor may remain inside the resin during the hardening period or while
left under normal storage conditions resulting in the deterioration of the capacitor's performance.
2. When a resin's hardening temperature is higher than capacitor's operating temperature, the stresses generated by the excessive heat
may lead to damage or destruction of capacitors.
Precautions
The use of such resins, molding materials etc. is not recommended.
7. Handling
◆Splitting of PCB
1. When PCBs are split after components mounting, care shall be taken so as not to give any stresses of deflection or twisting to the board.
2. Board separation shall not be done manually, but by using the appropriate devices.
◆Mechanical considerations
Precautions
Be careful not to subject capacitors to excessive mechanical shocks.
（1）If ceramic capacitors are dropped onto a floor or a hard surface, they shall not be used.
（2）Please be careful that the mounted components do not come in contact with or bump against other boards or components.
8. Storage conditions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep packaging materials in good condition, care must be taken to control
temperature and humidity in the storage area. Humidity should especially be kept as low as possible.
・Recommended conditions
Ambient temperature : Below 30℃
Humidity : Below 70% RH
Precautions
The ambient temperature must be kept below 40℃. Even under ideal storage conditions, solderability of capacitor is deteriorated as
time passes, so capacitors shall be used within 6 months from the time of delivery.
・Ceramic chip capacitors shall be kept where no chlorine or sulfur exists in the air.
2. The capacitance values of high dielectric constant capacitors will gradually decrease with the passage of time, so care shall be taken to
design circuits. Even if capacitance value decreases as time passes, it will get back to the initial value by a heat treatment at 150℃ for
1hour.
If capacitors are stored in a high temperature and humidity environment, it might rapidly cause poor solderability due to terminal oxidation and
quality loss of taping/packaging materials. For this reason, capacitors shall be used within 6 months from the time of delivery. If exceeding the
above period, please check solderability before using the capacitors.
Technical
considerations
※RCR-2335B（Safety Application Guide for fixed ceramic capacitors for use in electronic equipment）is published by JEITA.
Please check the guide regarding precautions for deflection test, soldering by spot heat, and so on.
▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
c_mlcc_prec_e-E05R01
5秒后页面跳转
CP2102资料手册解读：CP2102引脚说明、关键参数分析
资料手册解读：UC3842参数和管脚说明
一文带你了解无源晶振的负载电容为何要加两颗谐振电容CL1和CL2
玻璃管保险丝与陶瓷管保险丝：区别与替代性探讨
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
