5秒后页面跳转
LM75B_V01 PDF预览

LM75B_V01

更新时间: 2024-11-27 02:48:19
品牌 Logo 应用领域
恩智浦 - NXP /
页数 文件大小 规格书
37页 555K
描述
Digital temperature sensor and thermal watchdog

LM75B_V01 数据手册

 浏览型号LM75B_V01的Datasheet PDF文件第2页浏览型号LM75B_V01的Datasheet PDF文件第3页浏览型号LM75B_V01的Datasheet PDF文件第4页浏览型号LM75B_V01的Datasheet PDF文件第5页浏览型号LM75B_V01的Datasheet PDF文件第6页浏览型号LM75B_V01的Datasheet PDF文件第7页 
LM75B  
Digital temperature sensor and thermal watchdog  
Rev. 6.1 — 6 February 2015  
Product data sheet  
1. General description  
The LM75B is a temperature-to-digital converter using an on-chip band gap temperature  
sensor and Sigma-Delta A-to-D conversion technique with an overtemperature detection  
output. The LM75B contains a number of data registers: Configuration register (Conf) to  
store the device settings such as device operation mode, OS operation mode, OS polarity  
and OS fault queue as described in Section 7 “Functional description”; temperature  
register (Temp) to store the digital temp reading, and set-point registers (Tos and Thyst) to  
store programmable overtemperature shutdown and hysteresis limits, that can be  
communicated by a controller via the 2-wire serial I2C-bus interface. The device also  
includes an open-drain output (OS) which becomes active when the temperature exceeds  
the programmed limits. There are three selectable logic address pins so that eight devices  
can be connected on the same bus without address conflict.  
The LM75B can be configured for different operation conditions. It can be set in normal  
mode to periodically monitor the ambient temperature, or in shutdown mode to minimize  
power consumption. The OS output operates in either of two selectable modes:  
OS comparator mode or OS interrupt mode. Its active state can be selected as either  
HIGH or LOW. The fault queue that defines the number of consecutive faults in order to  
activate the OS output is programmable as well as the set-point limits.  
The temperature register always stores an 11-bit two’s complement data giving a  
temperature resolution of 0.125 C. This high temperature resolution is particularly useful  
in applications of measuring precisely the thermal drift or runaway. When the LM75B is  
accessed the conversion in process is not interrupted (that is, the I2C-bus section is totally  
independent of the Sigma-Delta converter section) and accessing the LM75B  
continuously without waiting at least one conversion time between communications will  
not prevent the device from updating the Temp register with a new conversion result. The  
new conversion result will be available immediately after the Temp register is updated.  
The LM75B powers up in the normal operation mode with the OS in comparator mode,  
temperature threshold of 80 C and hysteresis of 75 C, so that it can be used as a  
stand-alone thermostat with those pre-defined temperature set points.  
2. Features and benefits  
Pin-for-pin replacement for industry standard LM75 and LM75A and offers improved  
temperature resolution of 0.125 C and specification of a single part over power supply  
range from 2.8 V to 5.5 V  
I2C-bus interface with up to 8 devices on the same bus  
Power supply range from 2.8 V to 5.5 V  
Temperatures range from 55 C to +125 C  
 
 

与LM75B_V01相关器件

型号 品牌 获取价格 描述 数据表
LM75BD NXP

获取价格

Digital temperature sensor and thermal watchdog
LM75BD UMW

获取价格

温度感应器
LM75BD,112 NXP

获取价格

LM75B - Digital temperature sensor and thermal watchdog SOIC 8-Pin
LM75BD,118 NXP

获取价格

LM75B - Digital temperature sensor and thermal watchdog SOIC 8-Pin
LM75BDP NXP

获取价格

Digital temperature sensor and thermal watchdog
LM75BDP UMW

获取价格

温度感应器
LM75BDP,118 NXP

获取价格

LM75B - Digital temperature sensor and thermal watchdog TSSOP 8-Pin
LM75BDP/DG,118 NXP

获取价格

Digital temperature sensor and thermal watchdog
LM75BGD NXP

获取价格

Digital temperature sensor and thermal watchdog
LM75BGD,125 NXP

获取价格

LM75B - Digital temperature sensor and thermal watchdog SON 8-Pin