Pin Descriptions
Pin(S)
Name
Description
Application Information
1
VCC
Output of the bias regulator
Vcc tracks Vin up to 9V. Beyond 9V, Vcc is regulated to 7
Volts. A 0.1uF to 1uF ceramic decoupling capacitor is
required. An external voltage (7.5V – 14V) can be applied
to this pin to reduce internal power dissipation.
2
SD
Shutdown or UVLO input
If the SD pin voltage is below 0.7V the regulator will be in a
low power state. If the SD pin voltage is between 0.7V and
1.225V the regulator will be in standby mode. If the SD pin
voltage is above 1.225V the regulator will be operational. An
external voltage divider can be used to set a line
undervoltage shutdown threshold. If the SD pin is left open
circuit, a 5µA pull-up current source configures the regulator
fully operational.
3, 4
5
Vin
Input supply voltage
Nominal operating range: 7V to 42V
SYNC
Oscillator synchronization input or output The internal oscillator can be synchronized to an external
clock with an external pull-down device. Multiple LM25005
devices can be synchronized together by connection of their
SYNC pins.
6
7
8
COMP
FB
Output of the internal error amplifier
The loop compensation network should be connected
between this pin and the FB pin.
Feedback signal from the regulated
output
This pin is connected to the inverting input of the internal
error amplifier. The regulation threshold is 1.225V.
RT
Internal oscillator frequency set input
The internal oscillator is set with a single resistor, connected
between this pin and the AGND pin. The recommended
frequency range is 50KHz to 500KHz.
9
RAMP
Ramp control signal
An external capacitor connected between this pin and the
AGND pin sets the ramp slope used for current mode
control. Recommended capacitor range 50pF to 2000pF.
10
11
AGND
SS
Analog ground
Soft-start
Internal reference for the regulator control functions
An external capacitor and an internal 10µA current source
set the time constant for the rise of the error amp reference.
The SS pin is held low during standby, Vcc UVLO and
thermal shutdown.
12
OUT
Output voltage connection
Power ground
Connect directly to the regulated output voltage.
13, 14
PGND
Low side reference for the PRE switch and the IS sense
resistor.
15, 16
IS
Current sense
Current measurement connection for the re-circulating
diode. An internal sense resistor and a sample/hold circuit
sense the diode current near the conclusion of the off-time.
This current measurement provides the DC level of the
emulated current ramp.
17, 18
19
SW
Switching node
The source terminal of the internal buck switch. The SW pin
should be connected to the external Schottky diode and to
the buck inductor.
PRE
Pre-charge assist for the bootstrap
capacitor
This open drain output can be connected to SW pin to aid
charging the bootstrap capacitor during very light load
conditions or in applications where the output may be pre-
charged before the LM25005 is enabled. An internal pre-
charge MOSFET is turned on for 250ns each cycle just prior
to the on-time interval of the buck switch.
3
www.national.com
5秒后页面跳转
STM32H743技术深度剖析与应用案例探索
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
74HC14芯片资料介绍：性能特性分析、引脚介绍
LM1875芯片手册：功放参数分析、引脚说明、电路设计要点
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
