ALUMINUM ELECTROLYTIC CAPACITORS
Snap-in Terminal Type, 105°C Permissible Abnormal Voltage,
Smaller-sized
AQ (692 type) series
Withstanding 2000 hours application of rated ripple current of 105°C.
Extended voltage range at 200V, 220V and 400V.
AK
Smaller case sizes and higher ripple current than AK series.
Smaller
Improved safety features for abnormally excessive voltage.
Ideally suited for the equipment used at voltage fluctuating area.
Compliant to the RoHS directive (2002/95/EC).
AQ
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
–25 to +105°C
200 • 220 • 400V
33 to 1500µF
±20% at 120Hz, 20°C
[
(
)
( )]
µ
3
I
C : Rated Capacitance µF V : Voltage V
CV ( A) (After 5 minutes' application of rated voltage)
Tangent of loss angle (tan δ) 0.20MAX. 120Hz, 20°C
Rated voltage(V)
200
•
220
400
8
Measurement frequency : 120Hz
Stability at Low Temperature
(
)
–
25°C/Z+20°C
Impedance ratio MAX
The specifications listed at right shall be met when the
capacitors are restored to 20 after D.C. bias plus rated
Z
8
Within ±20% of the initial capacitance value
200% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan δ
°C
Endurance
ripple current is applied for 2000 hours at 105 , the
°C
peak voltage shall not exceed the rated voltage.
Leakage current
After storing the capacitors under no load at 105°C for 1000
hours and then performing voltage treatment based
on JIS C 5101-4 clause 4.1 at 20°C,
Within ±15% of the initial capacitance value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan δ
Shelf Life
Leakage current
they shall meet the requirements listed at right.
The pressure relief vent will operate in normal conditions, with no dangerous conditions such as flames, ignitions or dispersion of pieces of the capacitor and / or case.
Rating Test conditions
Voltage (V)
Rated Capacitance (µF)
<
Limited DC current
Test voltage
4 A
5 A
7 A
4 A
5 A
7 A
2 A
4 A
7 A
330
330
470
330
330
470
330
100
220
C
C
330
470
<
200
300VDC and 375VDC
C < 470
<
Safety Performance
C
C
330
470
<
220
400
320VDC and 405VDC
500VDC and 600VDC
C < 470
<
C
C
100
220
<
C < 470
Printed with white color letter on black sleeve
Marking
Drawing
Type numbering system (Example : 200V 680 F)
µ
Polarity bar
Bottom plate
(code ZB only)
(
)
Sleeve P.E.T.
1
2
3
4
5
6
7
8
9
10 11 12
13 14 15 16
L A Q 2 D 6 8 1 M E L A
4 0
Bottom Plate
Case length code
Case dia. code
With Bottom
Plate
ZB
Without
code less
Configuration
Bottom Plate
φD
22
25
30
35
Code
±2
L
Z
A
B
C
4.0±0.5
Capacitance tolerance (±20%)
Rated capacitance (680µF)
Rated voltage (200V)
Pressure relief vent
+0.2
-0.1
0.8
Series name
Type
Please contact to us if other configurations are required.
±0.1
φ
2-2
+0.2
-0.1
1.5
(PC board hole dimensions)
(Terminal dimensions)
Minimum order quantity : 50pcs.
Dimension table in next page.
CAT.8100A-1