3MHz Dual Step-Down Converters and Dual Low-Input
2
LDOs with I C Compatible Interface
ISL9305
Features
The ISL9305 is an integrated mini Power Management IC
(mini-PMIC) ideal for applications of powering low-voltage
microprocessor or multiple voltage rails with battery as input
sources, such as a single Li-ion or Li-Polymer. ISL9305
integrates two high-efficiency 3MHz synchronous step-down
converters (DCD1 and DCD2) and two low-input, low-dropout
linear regulators (LDO1 and LDO2).
• Dual 800mA, Synchronous Step-down Converters and Dual
300mA, General-purpose LDOs
• Input Voltage Range
- DCD1/DCD2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3V to 5.5V
- LDO1/LDO2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5V to 5.5V
2
• 400kb/s I C-bus Series Interface Transfers the Control Data
Between the Host Controller and the ISL9305
The 3MHz PWM switching frequency allows the use of very
small external inductors and capacitors. Both step-down
converters can enter skip mode under light load conditions to
further improve the efficiency and maximize the battery life.
For noise sensitive applications, they can also be programmed
• Adjustable Output Voltage
- DCD1/DCD2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8V to V
IN
2
- Fixed Output I C Programmability
2
• At 25mV/step. . . . . . . . . . . . . . . . . . . . . . . . . . .0.825V to 3.6V
through I C interface to operate in forced PWM mode
2
2
regardless of the load current condition. The I C interface
• LDO1/LDO2 Output Voltage I C Programmability
supports on-the-fly slew rate control of the output voltage from
0.825V to 3.6V at 25mV/step size for dynamic power saving.
Each step-down converter can supply up to 800mA load
- At 50mV/step. . . . . . . . . . . . . . . . . . . . . . . . . . . 0.9V to 3.3V
• 50μA I (Typ) with DCD1/DCD2 in Skip Mode; 20μA I (Typ)
Q
Q
for each Enabled LDO
current. The default output voltage can be set from 0.8V to V
IN
2
using external feedback resistors on the adjustable version, or
the ISL9305 can be ordered in factory pre-set power-up default
voltages in increments of 100mV from 0.9V to 3.6V.
• On-the-fly I C Programming of DC/DC and LDO Output
Voltages
2
• DCD1/DCD2 I C Programmable Skip Mode Under Light
The ISL9305 also provides two 300mA low dropout (LDO)
regulators. The input voltage range is 1.5V to 5.5V allowing
them to be powered from one of the on-chip step-down
converters or directly from the battery. The default LDO
power-up output comes with factory pre-set fixed output
voltage options between 0.9V to 3.3V.
Load or Forced Fixed Switching Frequency PWM Mode
• Small, Thin, 4mmx4mm TQFN Package
Applications
• Cellular Phones, Smart Phones
• PDAs, Portable Media Players, Portable Instruments
• Single Li-ion/Li-Polymer Battery-Powered Equipment
• DSP Core Power
The ISL9305 is available in a 4mmx4mm 16 Ld TQFN
package.
Related Literature
• FN7724, ISL9305H Data Sheet
• AN1564 “ISL9305IRTZEVAL1Z and ISL9305HIRTZEVAL1Z
Evaluation Boards”
L
L
= 1.5µH
1
800mA
PG
SW1
FB1
2.3V TO 5.5V
VINDCD1
*
R
1
C
4
R
VINDCD2
2
C
4.7µF
10
10µF
= 1.5µH
2
800mA
SDAT
SCLK
SW2
FB2
*
ISL9305
R
C
1.5V TO 5.5V
1.5V TO 5.5V
3
5
R
4
VINLDO1
4.7µF
C
2
1µF
300mA
300mA
VOLDO1
VOLDO2
VINLDO2
C
1µF
3
C
C
7
GNDDCD1GNDDCD2GNDLDO
6
1µF
1µF
*Only for adjustable output version. For fixed output version, directly
connect the FB pin to the output of the buck converter.
FIGURE 1. TYPICAL APPLICATION DIAGRAM
August 15, 2011
FN7605.1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 |Copyright Intersil Americas Inc. 2010, 2011. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
1