ISL9219R5360
¬
Data Sheet
December 4, 2009
FN6823.1
USB Compliant Li-ion Battery Charger
Features
The ISL9219R5360 is a fully integrated high input voltage
single-cell Li-ion battery charger. These chargers are fully in
compliance with the USB electrical specification. The
chargers perform the CC/CV charge function required by
Li-ion batteries. The chargers accept an input voltage up to
28V but are disabled when the input voltage exceeds the
OVP threshold, to prevent excessive power dissipation. The
28V rating eliminates the overvoltage protection circuit
required in a low input voltage charger.
• Complete Charger for Single-Cell Li-ion/Polymer Batteries
• Integrated Pass Element and Current Sensor
• No External Blocking Diode Required
• Low Component Count and Cost
• 0.7% Voltage Accuracy
• Programmable Charge Currents
• 250µA (Typ) Suspend Quiescent Current
• USB 100mA/500mA Charge Current Setting
• Charge Current Thermal Foldback for Thermal Protection
• Trickle Charge for Fully Discharged Batteries
• 28V Maximum Voltage for the Power Input
• Charge Status Indication
The fast charge current is programmable with an external
resistor, and the end-of-charge (EOC) current is fixed at
50mA for any input source type. When the input power
source is identified as a USB port, the host controller will
further identify the power type of the port and drive the USBI
pin accordingly.
When the battery voltage is lower than the trickle charge
threshold, which is also programmable with an external
resistor, the charger preconditions the battery with an 85mA
constant current. Charge is complete when the charge current
reduces to the EOC current level during the CV charge phase.
The STAT1 and STAT2 provide unique indication for each
charging condition. An internal thermal foldback function
protects the charger from any thermal failure.
• Less than 1µA Leakage Current Off the Battery when No
Input Power Attached or Charger Disabled
• Ambient Temperature Range: -40°C to +85°C
• Pb-free (RoHS Compliant)
Related Literature
• Technical Brief TB363 “Guidelines for Handling and
Processing Moisture Sensitive Surface Mount Devices
(SMDs)”
The STAT1 and STAT2 pins are of open drain type, allowing
a simple interface to a microprocessor or an LED. When no
adapter is attached or when disabled, the charger draws less
than 1µA leakage current from the battery.
• Technical Brief TB379 “Thermal Characterization of
Packaged Semiconductor Devices”
• Technical Brief TB389 “PCB Land Pattern Design and
Surface Mount Guidelines for QFN Packages”
Additional features include an OVP protected power-good
source, preconditioning of an over-discharged battery, an
NTC thermistor interface for charging the battery in a safe
temperature range, automatic recharge, and thermally
enhanced QFN package.
Pinout
ISL9219R5360
(20 LD 3X4 QFN)
TOP VIEW
Ordering Information
TEMP.
RANGE
(°C)
20
19
18 17
PART
NUMBER
PART
MARKING
PACKAGE
(Pb-Free)
PKG.
DWG. #
16
VOUT
VIN
USBI
1
2
3
4
5
6
15 TS
14 PG
ISL9219IRZR5360
219
-40 to +85 20 Ld 3x4 QFN L20.3x4
-40 to +85 20 Ld 3x4 QFN L20.3x4
AC_IN
TRKL
ISL9219IRZ-TR5360* 219
13
NC
12
TIMER
*Please refer to TB347 for details on reel specifications.
STAT1
STAT2
NOTE: These Intersil Pb-free plastic packaged products employ special
Pb-free material sets, molding compounds/die attach materials, and
100% matte tin plate plus anneal (e3 termination finish, which is RoHS
compliant and compatible with both SnPb and Pb-free soldering
operations). Intersil Pb-free products are MSL classified at Pb-free peak
reflow temperatures that meet or exceed the Pb-free requirements of
IPC/JEDEC J STD-020.
11
GND
7
8
9
10
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2009. All Rights Reserved
1
All other trademarks mentioned are the property of their respective owners.