DATASHEET
ISL9219
Li-ion Battery Charger
FN6606
Rev 2.00
April 7, 2010
The ISL9219 is a fully integrated high input voltage
single-cell Li-ion battery charger. This charger is fully in
compliance with the USB electrical specification. The
charger performs the CC/CV charge function required by
Li-ion batteries. The charger accepts an input voltage up to
28V but is disabled when the input voltage exceeds the OVP
threshold, typically 6V, to prevent excessive power
dissipation. The 28V rating eliminates the overvoltage
protection circuit required in a low input voltage charger.
Features
• Complete Charger for Single-Cell Li-ion/Polymer Batteries
• Integrated Pass Element and Current Sensor
• No External Blocking Diode Required
• Low Component Count and Cost
• 0.7% Voltage Accuracy
• Programmable Charge Currents
The fast charge current is programmable with an external
resistor, and the end-of-charge (EOC) current is fixed at
50mA for any input source type. When the input power
source is identified as a USB port, the host controller will
further identify the power type of the port and drive the USBI
pin accordingly.
• 250µA (Typ) Suspend Quiescent Current
• USB 100mA/500mA Comply
• Charge Current Thermal Foldback for Thermal Protection
• Trickle Charge for Fully Discharged Batteries
• 28V Maximum Voltage for the Power Input
• Charge Status Indication
When the battery voltage is lower than the pre-charge
threshold, which is also programmable with an external
resistor, the charger preconditions the battery with an 85mA
constant current. Charge is complete when the charge current
reduces to the EOC current level during the CV charge phase.
The STAT1 and STAT2 provide unique indication for each
charging condition. An internal thermal foldback function
protects the charger from any thermal failure.
• Less than 1µA Leakage Current Off the Battery when No
Input Power Attached or Charger Disabled
• Ambient Temperature Range: -40°C to +85°C
• Pb-free (RoHS Compliant)
Related Literature
• Technical Brief TB363 “Guidelines for Handling and
Processing Moisture Sensitive Surface Mount Devices
(SMDs)”
The STAT1, STAT2, TRKL and ACFLT pins are of open drain
type, allowing a simple interface to a microprocessor or an
LED. When no adapter is attached or when disabled, the
charger draws less than 1µA leakage current from the
battery.
• Technical Brief TB379 “Thermal Characterization of
Packaged Semiconductor Devices”
• Technical Brief TB389 “PCB Land Pattern Design and
Surface Mount Guidelines for QFN Packages”
Additional features include an OVP protected power-good
source, preconditioning of an over-discharged battery, an
NTC thermistor interface for charging the battery in a safe
temperature range, automatic recharge, and thermally
enhanced QFN package.
Pinout
ISL9219
(20 LD 3X4 QFN)
TOP VIEW
Ordering Information
PART
NUMBER
PART
TEMP.
PKG.
20 19 18 17
MARKING RANGE (°C) PACKAGE DWG. #
VIN
USBI
VOUT
TS
1
2
3
4
5
6
16
15
14
13
12
11
ISL9219IRZ*
219 -40 to +85 20 Ld 3x4 QFN L20.3x4
*Add “-T” suffix for tape and reel. Please refer to TB347 for details on
reel specifications.
AC_IN
TRKL
STAT1
STAT2
PG
NOTE: These Intersil Pb-free plastic packaged products employ
special Pb-free material sets, molding compounds/die attach
materials, and 100% matte tin plate plus anneal (e3 termination finish,
which is RoHS compliant and compatible with both SnPb and Pb-free
soldering operations). Intersil Pb-free products are MSL classified at
Pb-free peak reflow temperatures that meet or exceed the Pb-free
requirements of IPC/JEDEC J STD-020.
NC
TIMER
GND
7
8
9
10
FN6606 Rev 2.00
April 7, 2010
Page 1 of 12