High-Speed USB 2.0 (480Mbps) DPST Switch with
Overvoltage Protection (OVP) and Dedicated
Charger Port Detection
ISL54226
Features
• High-Speed (480Mbps) and Full-Speed (12Mbps)
Signaling Capability per USB 2.0
The Intersil ISL54226 is a single supply, dual SPST
(Single Pole/Single Throw) switch that is configured as a
DPST. It can operate from a single 2.7V to 5.25V supply.
The part was designed for switching or isolating a USB
high-speed source or a USB high-speed and full-speed
source in portable battery powered products.
• 1.8V Logic Compatible (2.7V to +3.6V Supply)
• OE/ALM Pin to Open all Switches and Indicate
Overvoltage Fault Condition
• Charger Interrupt Indicator Output
• Power OFF Protection
The 3.5Ω SPST switches were specifically designed to
pass USB full speed and USB high-speed data signals.
They have high bandwidth and low capacitance to pass
USB high-speed data signals with minimal distortion.
• COM Pins Overvoltage Protection for +5.25V and -5V
Fault Voltages
• -3dB Frequency . . . . . . . . . . . . . . . . . . . . 790MHz
• Low ON Capacitance @ 240MHz. . . . . . . . . . . . 2pF
• Low ON-Resistance. . . . . . . . . . . . . . . . . . . . 3.5Ω
The ISL54226 has OVP detection circuitry on the COM
pins to open the SPST switches when the voltage at
these pins exceeds 3.8V or goes negative by -0.45V. It
isolates fault voltages up to +5.25V or down to -5V from
getting passed to the other side of the switch, thereby
protecting the USB down-stream transceiver.
• Single Supply Operation (V ) . . . . . 2.7V to 5.25V
DD
• Available in µTQFN and TDFN Packages
• Pb-Free (RoHS Compliant)
The OE/ALM logic pin is an open drain input/output that
can be driven to open the switches or monitored to tell
when the part is in an overvoltage state.
• Compliant with USB 2.0 Short Circuit and
Overvoltage Requirements without Additional
External Components
The part has an interrupt (INT) output pin to indicate a
1 to 1 (high/high) state on the COM lines to inform the
µprocessor when entering a dedicated charging port
mode of operation.
Applications*(see page 16)
• MP3 and Other Personal Media Players
• Cellular/Mobile Phones, PDA’s
• Digital Cameras and Camcorders
• USB Switching
The ISL54226 is available in 8 Ld 1.2mmx1.4mm
µTQFN and 8 Ld 2mmx2mm TDFN packages. It operates
over a temperature range of -40 to +85°C.
Typical Application
USB 2.0 HS Eye Pattern with
Switches in the Signal Path
3.3V
3.3V
500Ω
100kΩ
VDD
INT
OE/ALM
D-
LOGIC
CONTROL
µP
VBUS
D-
COM -
USB
OVP
DET
COM +
HIGH-SPEED
TRANSCEIVER
4MΩ
D+
D+
ISL54226
GND
GND
TIME SCALE (0.2ns/DIV)
July 29, 2010
FN7614.0
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2010. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.