.002
.005
((No OF POS x .050) + .015)
REVISION R
FIG. 1
ISDF-XX-D-X
R
C1
ISDF-10-D-X SHOWN
SEE NOTE 2
OPTIONS
(No OF POS x .050) - .050
(TOL NON-ACCUM)
No OF POSITIONS
-02 THRU -50
(PER ROW)
R.001
R
LEAVE BLANK: NO KEY
DO NOT
SCALE FROM
THIS PRINT
-C: CHAMFER (SEE SHEET 2,
FIG 2) (7 POSITION ONLY)
-L: FRICTION LOCK
.025 (TYP)
C
L
"A"
.020 (TYP)
R
(SEE SHEET 2, FIG 3)
(AVAILABLE ON POS *5,*7,10 THRU 50)
-R: RETENTION LATCH (AVAILABLE
ON POS -02 THRU -50)
.250
.180
(SEE SHEET 3, FIG 4)
C
L
.120
.1450
(SEE NOTE 11)
ROW SPECIFICATION
-D: DOUBLE ROW
A
"A"
R
*=NOT AVAILABLE WITH POLARIZATION KEY
.003
SEE NOTE 3
.033
.0800±.0020
.050
C5
.030
"B"
SEE NOTE 4
'C'
.0500
.030
C
L
.050
.058
C4
.415
.440
.4260
R.015 TYP
.103
.077
.003
R.001
C2
.0420
"B"
'E'
C8
.0260
C3
.0525
.0430
.2180
SECTION "A"-"A"
C7
SEE NOTE 8
.0150 REF
'D'
"F"
SEE NOTE 7
C6
.0410
02 04 06 08 10 12 14 16 18 20
SECTION "B"-"B"
C
L
.070
SEE NOTE 12
01
05 07 09 11
15 17 19
13
03
NOTES:
1. C REPRESENTS A CRITICAL DIMENSION.
2. SAMTEC LOGOS SHALL APPEAR AT LOCATIONS ON SURFACE SHOWN,
APPROXIMATELY .075 x .055 (BOTH SIDES).
"F"
SECTION "F"-"F"
3. ALL MULTIPLE CAVITY MOLDS SHALL IDENTIFY EACH CAVITY WITH A LETTER
DESIGNATION LOCATED WHERE SHOWN.
4. IDENTIFICATION MARKS NOT TO PROTRUDE BEYOND .001 ABOVE THE SURFACE
OF THE INSULATOR MATERIAL.
PROPRIETARY NOTE
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DECIMALS
ANGLES
2
5. MOLDED SURFACES SHALL BE CONSISTENT AND SMOOTH. SURFACES TO BE
FREE OF SCATCHES, NICKS, SINK AREAS, VOIDS OR OTHER BLEMISHES.
6. PART TO BE SYMMETRIC ABOUT THE CENTERLINE WITHIN +/-.0015, UNLESS
OTHERWISE STATED.
.XX: .01 [.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
.XXX: .003 [.08]
PHONE: 812-944-6733
FAX: 812-948-5047
code: 55322
.XXXX: .0015 [.038]
e-Mail: info@SAMTEC.com
SHEET SCALE: 4:1
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
7. GATE PADS MUST BE RECESSED .005.
VECTRA S475, COLOR: BLACK
MAX REGRIND: 50%
8. SPECIFIED POSITIONS TO BE IDENTIFIED WHERE SHOWN (NOTE 4 APPLIES).
9. R.005 OPTIONAL.
10. POSITIONS -05, -10 THROUGH -24 WILL HAVE ONLY ONE LATCH LOCK AT DIMENSION SHOWN;
POSITIONS -25 THROUGH -50 WILL HAVE TWO LATCH LOCKS AT DIMENSION SHOWN.
11. OPTION NOT FOR SALE. FOR RETENTION LATCH FEATURE, SEE ISDF-XX-D-M PRINT.
12. .025 DIA EJ PADS CAN BE LOCATED AT VENDORS DISCRETION.
.050" CL CRIMP WIRE SOCKET INSULATOR
DWG. NO.
ISDF-XX-D-X
MAX FLASH ALLOWED: .002
MAX GATE VESTIGE: .004
BY:
BRATCHER 5/4/2005
SHEET 1 OF 3
c:\enterprisevault\DWG\MISC\MKTG\ISDF-XX-D-X-MKT.SLDDRW