.002
.005
((No OF POS x .050) + .015)
REVISION W
ISDF-XX-D-XX
FIG 1
C1
ISDF-10-D-X SHOWN
SEE NOTE 2
OPTIONS
(No OF POS x .050) - .050
(TOL NON-ACCUM)
No OF POSITIONS
R.001
LEAVE BLANK: NO KEY
-C: CHAMFER (SEE SHEET 2,
FIG 2) (7 POSITION ONLY)
-L: FRICTION LOCK
DO NOT
SCALE FROM
THIS PRINT
-02 THRU -50
.025 (TYP)
(PER ROW)
C
L
"A"
.020 (TYP)
(SEE SHEET 2, FIG 3)
(AVAILABLE ON POS *5,*7,10 THRU 50)
-R: RETENTION LATCH (AVAILABLE
ON POS -02 THRU -50)
(SEE SHEET 3, FIG 4)
.250
.180
C
L
.120
(SEE NOTE 11)
.1450
-DS: DUAL SCREW DOWN
(SEE SHEET 4, FIG 5)
A
"A"
(*=NOT AVAILABLE WITH POLARIZATION KEY)
.003
ROW SPECIFICATION
-D: DOUBLE ROW
.033
.0800±.0020
.050
C5
SEE NOTE 4
.030
"B"
'C'
.0500
.030
C
L
SEE NOTE 3
.050
.058
C4
.415
.440
.4260
R.015 TYP
.103
.077
.003
R.001
C2
C3
.0420
.0260
"B"
SECTION "A"-"A"
"F"
'E'
C8
.0525
.0430
.2180
C7
SEE NOTE 7
SEE NOTE 8
.0150 REF
C6
'D'
.0410
02 04 06 08 10 12 14 16 18 20
SECTION "B"-"B"
C
L
.070
SEE NOTE 12
01
05 07 09 11
15 17 19
13
03
NOTES:
C
1.
REPRESENTS A CRITICAL DIMENSION.
"F"
SECTION "F"-"F"
2. SAMTEC LOGOS SHALL APPEAR AT LOCATIONS ON SURFACE SHOWN,
APPROXIMATELY .075 x .055 (BOTH SIDES).
3. ALL MULTIPLE CAVITY MOLDS SHALL IDENTIFY EACH CAVITY WITH A LETTER
DESIGNATION LOCATED WHERE SHOWN.
4. IDENTIFICATION MARKS NOT TO PROTRUDE BEYOND .001 ABOVE THE SURFACE
OF THE INSULATOR MATERIAL.
5. MOLDED SURFACES SHALL BE CONSISTENT AND SMOOTH. SURFACES TO BE
FREE OF SCATCHES, NICKS, SINK AREAS, VOIDS OR OTHER BLEMISHES.
6. PART TO BE SYMMETRIC ABOUT THE CENTERLINE WITHIN +/-.0015, UNLESS
OTHERWISE STATED.
7. GATE PADS MUST BE RECESSED .005.
8. SPECIFIED POSITIONS TO BE IDENTIFIED WHERE SHOWN (NOTE 4 APPLIES).
9. R.005 OPTIONAL.
10. POSITIONS -05, -10 THROUGH -24 WILL HAVE ONLY ONE LATCH LOCK AT DIMENSION SHOWN;
POSITIONS -25 THROUGH -50 WILL HAVE TWO LATCH LOCKS AT DIMENSION SHOWN.
11. OPTION NOT FOR SALE. FOR RETENTION LATCH FEATURE, SEE ISDF-XX-D-M PRINT.
12. .031 MAXIMUM DIA EJ PADS CAN BE LOCATED AT VENDORS DISCRETION.
PROPRIETARY NOTE
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DECIMALS
ANGLES
2
.XX: .01 [.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
.XXX: .003 [.08]
PHONE: 812-944-6733
FAX: 812-948-5047
code: 55322
.XXXX: .0015 [.038]
e-Mail: info@SAMTEC.com
SHEET SCALE: 4:1
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
VECTRA S475, COLOR: BLACK
MAX REGRIND: 50%
.050" CL CRIMP WIRE SOCKET INSULATOR
DWG. NO.
ISDF-XX-D-XX
BRATCHER 5/4/2005
MAX FLASH ALLOWED: .002
MAX GATE VESTIGE: .004
SHEET 1 OF 4
BY:
c:\enterprisevault\DWG\MISC\MKTG\ISDF-XX-D-XX-MKT.SLDDRW