IS61DDPB42M18B/B1/B2
IS61DDPB41M36B/B1/B2
2Mx18, 1Mx36
NOVEMBER 2014
36Mb DDR-IIP(Burst 4) CIO SYNCHRONOUS SRAM
(2.5 Cycle Read Latency)
FEATURES
DESCRIPTION
The 36Mb IS61DDPB41M36B/B1/B2 and
1Mx36 and 2Mx18 configuration available.
IS61DDPB42M18B/B1/B2 are synchronous, high-
performance CMOS static random access memory (SRAM)
devices. These SRAMs have a common I/O bus. The rising
edge of K clock initiates the read/write operation, and all
internal operations are self-timed. Refer to the Timing
Reference Diagram for Truth Table for a description of the
basic operations of these DDR-IIP (Burst of 4) CIO SRAMs.
Read and write addresses are registered on alternating rising
edges of the K clock. Reads and writes are performed in
double data rate.
On-chip Delay-Locked Loop (DLL) for wide data
valid window.
Common I/O read and write ports.
Synchronous pipeline read with self-timed late write
operation.
Double Data Rate (DDR) interface for read and
write input ports.
2.5 cycle read latency.
Fixed 4-bit burst for read and write operations.
Clock stop support.
The following are registered internally on the rising edge of
the K clock:
Two input clocks (K and K#) for address and control
registering at rising edges only.
Read/write address
Read enable
Two echo clocks (CQ and CQ#) that are delivered
simultaneously with data.
Write enable
+1.8V core power supply and 1.5V to 1.8V VDDQ,
used with 0.75 to 0.9V VREF.
Byte writes
Data-in for first and third burst addresses
Data-out for second and fourth burst addresses
HSTL input and output interface.
Registered addresses, write and read controls, byte
writes, data in, and data outputs.
The following are registered on the rising edge of the K#
clock:
Full data coherency.
Byte writes
Boundary scan using limited set of JTAG 1149.1
functions.
Data-in for second and fourth burst addresses
Data-out for first and third burst addresses
Byte write capability.
Fine ball grid array (FBGA) package:
13mm x 15mm & 15mm x 17mm body size
165-ball (11 x 15) array
Byte writes can change with the corresponding data-in to
enable or disable writes on a per-byte basis. An internal write
buffer enables the data-ins to be registered one cycle after
the write address. The first data-in burst is clocked one cycle
later than the write command signal, and the second burst is
timed to the following rising edge of the K# clock. Two full
clock cycles are required to complete a write operation.
Programmable impedance output drivers via 5x
user-supplied precision resistor.
Data Valid Pin (QVLD).
ODT (On Die Termination) feature is supported
optionally on data inputs, K/K#, and BWx#.
During the burst read operation, the data-outs from the first
bursts are updated from output registers of the third rising
edge of the K# clock (starting two and half cycles later after
read command). The data-outs from the second burst are
updated with the fourth rising edge of the K clock where read
command receives at the first rising edge of K.
The end of top mark (B/B1/B2) is to define options.
IS61DDPB41M36B : Don’t care ODT function
and pin connection
IS61DDPB41M36B1 : Option1
IS61DDPB41M36B2 : Option2
Refer to more detail description at page 6 for each
ODT option.
The device is operated with a single +1.8V power supply and
is compatible with HSTL I/O interfaces.
Copyright © 2010 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time
without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to
obtain the latest version of this device specification before relying on any published information and before placing orders for products.
Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can
reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such
applications unless Integrated Silicon Solution, Inc. receives written assurance to its satisfaction, that:
a.) the risk of injury or damage has been minimized;
b.) the user assume all such risks; and
c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances
Integrated Silicon Solution, Inc.- www.issi.com
Rev. A
1
9/25/2014
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
