5秒后页面跳转
HO-P-411F PDF预览

HO-P-411F

更新时间: 2024-10-29 00:07:39
品牌 Logo 应用领域
莱姆 - LEM /
页数 文件大小 规格书
15页 1338K
描述
Current Transducer

HO-P-411F 数据手册

 浏览型号HO-P-411F的Datasheet PDF文件第1页浏览型号HO-P-411F的Datasheet PDF文件第3页浏览型号HO-P-411F的Datasheet PDF文件第4页浏览型号HO-P-411F的Datasheet PDF文件第5页浏览型号HO-P-411F的Datasheet PDF文件第6页浏览型号HO-P-411F的Datasheet PDF文件第7页 
HO 60 .. 250-P series  
Absolute maximum ratings  
Parameter  
Supply voltage (not destructive)  
Symbol  
Unit  
V
Value  
8
UC  
UC  
Supply voltage (not entering non standard modes)  
V
6.5  
Primary conductor temperature  
TB  
°C  
120  
2
ESD rating, Human Body Model (HBM)  
UESD  
kV  
Stresses above these ratings may cause permanent damage. Exposure to absolute maximum ratings for extended periods may  
degrade reliability.  
UL 508: Ratings and assumptions of certification  
File # E189713 Volume: 2 Section: 5  
Standards  
● CSA C22.2 NO. 14-10 INDUSTRIAL CONTROL EQUIPMENT - Edition 11 - Revision Date 2011/08/01  
● UL 508 STANDARD FOR INDUSTRIAL CONTROL EQUIPMENT - Edition 17 - Revision Date 2010/04/15  
Ratings  
Parameter  
Symbol  
Unit  
Value  
Primary involved potential  
V AC/DC  
600  
Max surrounding air temperature  
TA  
°C  
A
105  
According to series primary  
Primary current  
IP  
current  
Secondary supply voltage  
Output voltage  
UC  
V DC  
5
Vout  
V
0 to 5  
Conditions of acceptability  
1 - These devices have been evaluated for overvoltage category III and for use in pollution degree 2 environment.  
2 - A suitable enclosure shall be provided in the end-use application.  
3 - The terminals have not been evaluated for field wiring.  
4 - These devices are intended to be mounted on a printed wiring board of end use equipment. The suitability of the  
connections (including spacings) shall be determined in the end-use application.  
5 - Primary terminals shall not be straightened since assembly of housing case depends upon bending of the terminals.  
6 - Any surface of polymeric housing have not been evaluated as insulating barrier.  
7 - Low voltage control circuit shall be supplied by an isolating source (such as a transformer, optical isolator,  
limiting impedance or electro-mechanical relay).  
10 - The jumper installed within the primary hole is only intended for fixing the sensor and not for carrying the primary current.  
Marking  
Only those products bearing the UR Mark should be considered to be Listed or Recognized and covered under UL's Follow-Up  
Service. Always look for the Mark on the product.  
Page 2/15  
16July2015/Version 5  
LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice  
www.lem.com  

与HO-P-411F相关器件

型号 品牌 获取价格 描述 数据表
HO-P-411G LEM

获取价格

Current Transducer
HO-P-411H LEM

获取价格

Current Transducer
HO-P-4200 LEM

获取价格

Current Transducer
HO-P-4201 LEM

获取价格

Current Transducer
HO-P-4202 LEM

获取价格

Current Transducer
HO-P-4203 LEM

获取价格

Current Transducer
HO-P-4204 LEM

获取价格

Current Transducer
HO-P-4205 LEM

获取价格

Current Transducer
HO-P-4206 LEM

获取价格

Current Transducer
HO-P-4207 LEM

获取价格

Current Transducer