HIP6004E
®
Data Sheet
July 2004
FN4997.2
Buck and Synchronous-Rectifier (PWM)
Controller and Output Voltage Monitor
Features
• Drives two N-Channel MOSFETs
• Operates from +5V or +12V Input
• Simple single-loop control design
- Voltage-mode PWM control
• Fast transient response
The HIP6004E provides complete control and protection for a
DC-DC converter optimized for high-performance
microprocessor applications. It is designed to drive two
N-Channel MOSFETs in a synchronous-rectified buck topology.
The HIP6004E integrates all of the control, output adjustment,
monitoring and protection functions into a single package.
- High-bandwidth error amplifier
- Full 0% to 100% Duty Ratio
• Excellent output voltage regulation
The output voltage of the converter is easily adjusted and
precisely regulated. The HIP6004E includes a 5-input digital-
to-analog converter (DAC) that adjusts the output voltage
- ±1% Over Line Voltage and Temperature
• 5-Bit digital-to-analog output
Voltage Selection
from 1.05V
to 1.825V
in 25mV increments steps. The
DC
DC
precision reference and voltage-mode regulator hold the
selected output voltage to within ±1% over temperature and
line voltage variations.
- 25mV binary steps . . . . . . . . . . . 1.05V
• Power good output voltage monitor
to 1.825V
DC
DC
• Overvoltage and overcurrent fault monitors
- Does not require extra current sensing element,
Uses MOSFET’s r
The HIP6004E provides simple, single feedback loop,
voltage-mode control with fast transient response. It includes
a 200kHz free-running triangle-wave oscillator that is
adjustable from below 50kHz to over 1MHz. The error
amplifier features a 15MHz gain-bandwidth product and
6V/µs slew rate which enables high converter bandwidth for
fast transient performance. The resulting PWM duty ratio
ranges from 0% to 100%.
DS(ON)
• Small Converter Size
- Constant Frequency Operation
- 200kHz Free-Running Oscillator Programmable from
50kHz to over 1MHz
• Pb-free available
The HIP6004E monitors the output voltage with a window
comparator that tracks the DAC output and issues a Power
Good signal when the output is within ±10%. The HIP6004E
protects against over-current and overvoltage conditions by
inhibiting PWM operation. Additional built-in overvoltage
protection triggers an external SCR to crowbar the input
supply. The HIP6004E monitors the current by using the
Applications
• VRM8.5 modules for Pentium III and Other
Microprocessors
•
•
High-Power DC-DC Regulators
Low-Voltage Distributed Power Supplies
Related Literature
r
of the upper MOSFET which eliminates the need for
DS(ON)
a current sensing resistor.
• Technical Brief TB363 “Guidelines for Handling and
Processing Moisture Sensitive Surface Mount Devices
(SMDs)”
Pinout
HIP6004E
TOP VIEW
Ordering Information
TEMP.
PKG.
DWG. #
1
2
3
4
5
6
7
8
9
RT
VSEN
OCSET
SS
20
19
o
PART NUMBER RANGE ( C)
PACKAGE
20 Ld SOIC
OVP
HIP6004ECB
0 to 70
0 to 70
M20.3
M20.3
18 VCC
HIP6004ECBZ
(See Note)
20 Ld SOIC
(Pb-free)
VID25mV
VID0
17 LGATE
16 PGND
HIP6004ECV
0 to 70
0 to 70
20 Ld TSSOP
M20.173
M20.173
VID1
BOOT
15
HIP6004ECVZ
(See Note)
20 Ld TSSOP
(Pb-free)
VID2
14 UGATE
13 PHASE
*Add “-T” suffix to part number for tape and reel packaging.
VID3
12
NOTE: Intersil Pb-free products employ special Pb-free material sets; molding
compounds/die attach materials and 100% matte tin plate termination finish, which
is compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free
products are MSL classified at Pb-free peak reflow temperatures that meet or
exceed the Pb-free requirements of IPC/JEDEC J Std-020B.
COMP
PGOOD
FB 10
11 GND
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2001, 2004. All Rights Reserved
1
All other trademarks mentioned are the property of their respective owners.