HI-506, HI-507, HI-508, HI-509
Data Sheet
June 1999
File Number 3142.2
Single 16 and 8/Differential 8-Channel and
4-Channel CMOS Analog Multiplexers
Features
• Low ON Resistance . . . . . . . . . . . . . . . . . . . . . . . . . 180Ω
• Wide Analog Signal Range . . . . . . . . . . . . . . . . . . . . . ±15V
• TTL/CMOS Compatible
The HI-506/HI-507 and HI-508/HI-509 monolithic CMOS
multiplexers each include an array of sixteen and eight
analog switches respectively, a digital decoder circuit for
channel selection, voltage reference for logic thresholds, and
an enable input for device selection when several
multiplexers are present. The Dielectric Isolation (DI)
process used in fabrication of these devices eliminates the
problem of latchup. DI also offers much lower substrate
leakage and parasitic capacitance than conventional
junction isolated CMOS (see Application Notes AN520 and
AN521).
• Access Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250ns
• Maximum Power Supply. . . . . . . . . . . . . . . . . . . . . . . .44V
• Break-Before-Make Switching
• No Latch-Up
• Replaces DG506A/DG506AA and DG507A/DG507AA
• Replaces DG508A/DG508AA and DG509A/DG509AA
The switching threshold for each digital input is established by
an internal +5V reference, providing a guaranteed minimum
2.4V for logic “1” and maximum 0.8V for logic “0”. This allows
direct interface without pullup resistors to signals from most
logic families: CMOS, TTL, DTL and some PMOS. For
protection against transient overvoltage, the digital inputs
include a series 200Ω resistor and diode clamp to each
supply.
Applications
• Data Acquisition Systems
• Precision Instrumentation
• Demultiplexing
• Selector Switch
Ordering Information
The HI-506 is a single 16-Channel, the HI-507 is an
8-Channel differential, the HI-508 is a single 8-Channel and
the HI-509 is a 4-Channel differential multiplexer.
TEMP.
PKG.
NO.
o
PART NUMBER RANGE ( C)
PACKAGE
28 Ld SOIC
HI9P0506-9
HI3-0506-5
HI4P0506-5
HI1-0506-5
HI1-0506-4
HI1-0506-2
HI4P0507-5
HI3-0507-5
HI1-0507-2
HI1-0508-5
HI3-0508-5
HI1-0508-4
HI1-0508-2
HI4P0508-5
HI9P0508-9
HI9P0508-5
HI9P0509-5
HI1-0509-4
HI1-0509-5
HI3-0509-5
HI4P0509-5
HI1-0509-2
-40 to 85
0 to 75
M28.3
If input overvoltages are present, the HI-546/HI-547/HI-548/
HI-549 multiplexers are recommended.
28 Ld PDIP
E28.6
N28.45
F28.6
F28.6
F28.6
N28.45
E28.6
F28.6
F16.3
E16.3
F16.3
F16.3
N20.35
M16.15
M16.15
M16.15
F16.3
F16.3
E16.3
N20.35
F16.3
0 to 75
28 Ld PLCC
28 Ld CERDIP
28 Ld CERDIP
0 to 75
-25 to 85
-55 to 125 28 Ld CERDIP
0 to 75
0 to 75
28 Ld PLCC
28 Ld PDIP
-55 to 125 28 Ld CERDIP
0 to 75
0 to 75
16 Ld CERDIP
16 Ld PDIP
-25 to 85
16 Ld CERDIP
-55 to 125 16 Ld CERDIP
0 to 75
-40 to 85
0 to 75
0 to 75
-25 to 85
0 to 75
0 to 75
0 to 75
20 Ld PLCC
16 Ld SOIC
16 Ld SOIC
16 Ld SOIC
16 Ld CERDIP
16 Ld CERDIP
16 Ld PDIP
20 Ld PLCC
-55 to 125 16 Ld CERDIP
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
http://www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
1