F-217 (Rev 24MAY17)
HDTM–4–06–1–S–VT–0–1–1
HDTM–4–04–1–S–VT–5–R–1–C
HDTM–4–08–1–S–VT–5–R––1–C
(1.80 mm) .071"
HDTM SERIES
XCede® HD BACKPLANE HEADER
Keying
Mates with:
HDTF
SPECIFICATIONS
Guidance
For complete specifications and
recommended PCB layouts see
www.samtec.com?HDTM
Insulator Material:
Liquid Crystal Polymer
Contact Material:
Copper Alloy
Plating:
Sn or Au over
APPLICATION
50 µ" (1.27 µm) Ni
Operating Temp Range:
Testing Now!
Current Rating:
Testing Now!
RoHS Compliant:
Yes
4 mm
contact wipe
Three levels of
sequencing enable
hot plugging
Shown with optional power module
NO. OF
PAIRS
SIDE
WALLS
STAGE
COMBO
PLATING
GUIDE
KEY
HDTM
1
VT
COL.
–S
= 30 µ"
(0.76 µm)
Gold in
contact area,
MatteTin
on tail
–1
= 3 mm
Wipe
Signal /
4 mm
Wipe
Ground
(Only
available
with
–4 or –5
polarizing)
(Only available
with –4 or –5
polarizing)
–04
–0
(No Walls)
–3, –4, –6
= Four Columns
= Open
= Pairs Per Column
–06
(Leave Blank
for None)
= Six Columns
–4
(Leave
Blank
for None)
= Left Polarizing
–08
–L
= Eight Columns
–5
= Left Side
Guide Pin
= Right Polarizing
–A
thu
–H
= Position
of flat on
Key
B
C
D
–R
NO. OF
COLUMNS
A
Right
Left Two Right
Left
= Right Side
Guide Pin
Polarize
Wall Wall Wall Polarize
(7.06) (8.20) (9.20) (8.06) (13.54) (13.05)
.278 .322 .362 .317 .533 .513
–04
(10.66) (11.80) (12.80)(11.66) (17.14) (16.65)
.420 .465 .503 .459 .674 .656
GUIDANCE
KEYING
(See table
for Key)
–06
–A
–B
–C
–D
–E
–F
–G –H
(14.26) (15.40) (16.40)(15.26) ((20.74) (20.25)
.561 .606 .817 .600 .817 .797
A
A
A
A
A
A
A
A
B
H
B
H
B
H
F
B
H
F
B
H
F
B
H
F
B
H
B
H
F
–08
A
–L /–R
C
G
C
G
C
G
C
G
C
G
C
G
C
G
C
G
F
F
F
D
D
D
D
D
D
D
D
E
E
E
E
E
E
E
E
C
(1.80)
.071
(12.44) .490
(2.40)
.094
(20.86)
.821
(3.20)
.126
DIA
(0.19)
.007
(18.70)
.736
(16.75)
.659
(3.68)
.145
DIA
(2.26)
.090
(2.40)
.094
D
(12.00)
.472
B
Note:
XCede® HD is a
HDTM–4–06–1–X–VT–0–1– SHOWN
HDTM–4–04–1–X–VT–X–X–1–A SHOWN
trademark of Amphenol.
Due to technical progress, all designs, specifications and components are subject to change without notice.
WWW.SAMTEC.COM
All parts within this catalog are built to Samtec’s specifications.
Customer specific requirements must be approved by Samtec and identified in a Samtec customer-specific drawing to apply.