GLS85VM1004G / 1004Q (100-ball)
Industrial Grade eMMC NANDrive™ EX Series
Factsheet 01.200
March 2020
Features
• Industry Standard Embedded MultiMediaCard
• Integrated Voltage Detector
Detects supply voltage fluctuations and
(eMMC) Host Interface
–
–
–
JEDEC/MMC Standard Version 5.1
JESD84-B51 compliant
Backward compatible with previous eMMC
standards
generates reset during power-up and power-
down to prevent inadvertent writes
• Expanded Data Protection
–
Hardware Write Protection pin
• Performance
–
Data sanitization
–
–
–
–
–
–
eMMC clock speed: Up to 200MHz
eMMC data bus width: x1/x4/x8
Supports Dual Data Rate mode
Supports HS200 / HS400 modes
Sequential data read: Up to 160 MByte/sec*
Sequential data write: Up to 57 MByte/sec*
* measured in HS400 enhanced mode using 1 MByte
transfer size
• Latency Management
Reduces latency due to background tasks
during time critical read/write operations
• Supports SMART and TRIM Commands
• Robust Built-in ECC
–
• NAND Configuration
–
1 bit per cell (SLC)
–
Designed with Greenliant’s advanced
EnduroSLC™ Technology
• Power Management
–
–
–
3.3V power supply (VCC)
3.3V or 1.8V eMMC IO voltage (VCCQ
Immediate disabling of unused circuitry
without host intervention
• High Endurance
)
–
GLS85VM1004G: 50K P/E cycles
–
GLS85VM1004Q: 100K P/E cycles
• Operating Temperature Range
Industrial: -40°C to 85°C
• 100-ball LBGA Package
14.0 mm x 18.0 mm x 1.40 mm,
1.0 mm ball pitch, LFWE
• Power Specifications
–
–
Active mode: 471 mW (typical)
–
Sleep mode: 2.15mW (typical)
–
• All Devices are RoHS Compliant
Product Description
The GLS85VM1004G / 1004Q eMMC NANDrive™ EX
Series devices (referred to as “eMMC NANDrive” in
this factsheet) are fully integrated solid state drives.
They combine an advanced Greenliant NAND
controller and 4 GBytes of NAND flash memory in a
multi-chip package. These products are ideal for
embedded and portable applications that require small
form factor, high endurance and reliable data storage.
The integrated NAND flash controller with built-in
advanced NAND management firmware communicates
with the host through the standard eMMC protocol. It
does not require any additional or proprietary software
such as the Flash File System (FFS) and Memory
Technology Driver (MTD).
eMMC NANDrive’s advanced NAND management
technology enhances data security, improves
endurance and accurately tracks the usage of the
NAND flash. This innovative technology combines
robust error correction capabilities with advanced
wear-leveling algorithms and bad block management
to extend the life of the product.
eMMC solid state drives are widely used in GPS and
telematics, in-vehicle infotainment, portable and
industrial computers, handheld data collection
scanners, point-of-sale terminals, networking and
telecommunications equipment, robotics, audio and
video recorders, monitoring devices and set-top boxes.
eMMC NANDrive supports Single Data Rate (SDR)
and Dual Data Rate (DDR) modes, HS200 mode,
HS400 mode, boot, multiple partitions, permanent and
partial write protect, Replay Protected Memory Block
(RPMB) access, Sanitize and TRIM, hardware reset
and other features detailed in the eMMC 5.1 standard
specification. It is backward compatible with previous
eMMC standards
eMMC NANDrive provides complete eMMC solid state
drive (SSD) functionality and compatibility in a 14mm
x 18mm BGA package for easy, space saving
mounting to a system motherboard. With its small size,
low power consumption, strong security, reliability and
ruggedness, eMMC NANDrive surpasses removable
storage and discrete NAND-based products.
These specifications are subject to change without notice.
© 2020 Greenliant
03/12/2020
S71460-F
1
GLS FS0019 Rev. 00