GenesysTM 3U 15kW Specifications
15kW
1.0 MODEL
1.Rated Output Voltage
GEN
VDC
ADC
kW
N/A
---
N/A
---
N/A
---
---
---
---
N/A
---
---
---
---
N/A
---
---
---
---
30-500 40-375 50-300 60-250 80-187.5 100-150 125-120
X
X
X
X
X
X
30
40
50
60
250
15.0
88
80
100
150
15.0
125
120
15.0
2.Rated Output Current
---
---
500
15.0
375
15.0
300
15.0
187.5
15.0
3.Rated Output Power
---
---
4.Efficiency (min) at low AC line, 100% Rated Load
%
---
---
Contact Factory for other models
1.1 CONSTANT VOLTAGE MODE (CV)
1. Max. Line Reg (0.1% - Vor ≤ 30V; 0.05% - 30V < Vor <
600V; 0.05% - 600V < Vor < 1500V)
2. Max. Load Reg (0.1% - Vor ≤ 30V; 0.05% - 30V < Vor <
600V; 0.1% - 600V < Vor < 1500V)
mV
mV
---
---
---
---
---
---
---
---
---
---
30
30
20
20
25
25
30
30
40
40
50
50
62.5
62.5
X
X
3. Output Ripple, rms (5Hz~1MHz), CV mode; (*1)
4. Output Noise, p-p (20MHz), CV mode; (*1)
5.Remote Sense Compensation / Wire
6. Temperature Stability
mV
mV
V
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
20
60
1.5
20
60
2
20
75
3
20
75
3
25
100
4
25
100
5
25
125
5
X
X
X
X
X
X
X
X
---
± 0.05% of Vo(rated) over 8 hours after 30 minute warm up (constant Line, Load & Temperature)
7. Temperature Coefficient
ppm / °C ± 200 (± 0.02% of Vo(rated)) / °C
8. Up-Prog. Response Time, 0 ~ Vomax, full-load
9. Up-Prog. Response Time, 0~Vomax, no load
10. Transient Response Time (CV mode); (*2), (*3)
ms
ms
ms
100
50
Less than 3
1.2 CONSTANT CURRENT MODE (CC)
1. Max. Line Reg. (0.1% - Ior ≥ 333A; 0.050% - Ior < 333A)
2. Max. Load Reg (0.1% - Ior ≥ 333A; 0.075% - 25A < Ior <
333A; 0.2% - Ior < 25A)
3. Ripple, rms (5Hz~1MHz), CC mode
4. Temperature Stability
5. Temperature Coefficient
mA
mA
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
500
375
375
200
334
334
150
125
188
100
94
75
60
90
50
X
X
500
350
141
100
113
100
mA
---
ppm/°C
X
X
X
± 0.05% of Io(rated) over 8 hours after 30 minute warm up (constant Line, Load & Temperature)
± 300 (± 0.03% of Io(rated)) / °C
1.3 PROTECTIVE FUNCTIONS
1. OCP
2. OCP type
3. Foldback Protection (FOLD)
4. Foldback Response Time
5. OVP type
%
---
---
s
---
%
0 ~ 100
Constant current
X
X
X
X
X
X
Output shutdown; Manual reset by front panel OUT button or DIgital communication, user-selectable
Less than 1 (Min = 0.25 / Max = 25 / Default = 0.25); Settable via “FBD” command
Inverter shut-down; Manual reset by AC On/Off recycle, OUT button, Remote Analog or Digital communication
± 5% of Vo(rated)
6. OVP Programming Accuracy
5% to to 105% of Vo(rated) - for Vor < 600V; 10% to 105% of Vo(rated) - 600V < Vor < 1500V
Shall always be greater than 105% of Vo(setting); Default = 105% of Vo(rated)
Less than 10 (for Output to begin to drop) for Vor < 600V
7. OVP Trip Point
V
X
8. OVP Response Time
ms
X
Less than 2.0 (for Output to begin to drop) for 600V < Vor < 1500V
9. Max. OVP Reset Time
10. Over-temperature Protection (OTP)
11. Phase-Loss Protection
s
---
---
7 (from AC On/Off switch turn On)
Shut down if internal temperature exceeds safe operating levels (Latched: Safe / Unlatched: Auto)
Yes, power supply shutdown (Latched: Safe-Start / Unlatched: Auto-Restart)
X
X
X
1.4 REMOTE ANALOG CONTROLS & SIGNALS
1. Vout Voltage Programming
2. Iout Voltage Programming
3. Vout Resistor Programming
4. Iout Resistor Programming
5. Shut-Off (SO) Control (rear panel)
6. Output Current Monitor
7. Output Voltage Monitor
8. Power Supply OK (PS_OK) Signal
9. CV/CC Signal
0~100%, 0 ~ 5V or 0 ~ 10V, user-selectable., Accuracy & Linearity: ±1% of Vo(rated)
0~100%, 0 ~ 5V or 0 ~ 10V, user-selectable, Accuracy & Linearity: ± 1% of Io(rated)
0~100%, 0 ~ 5/10kohm full-scale, user-selectable, Accuracy & Linearity: ± 1% of Vo(rated)
0~100%, 0 ~ 5/10kohm full-scale, user-selectable, Accuracy & Linearity: ± 1% of Io(rated)
By Voltage: 0.6V = DIS, 2-15V = ENA (default) or Dry Contact: Open = ENA, Short = DIS (user-selectable logic)
0 ~ 5V or 0 ~ 10V, Accuracy: ± 1% of Io(rated), user-selectable
0 ~ 5V or 0 ~ 10V, Accuracy: ± 1% of Vo(rated), user-selectable
Yes. TTL High = OK, 0V = Fail (500ohm series impedance)
CV: TTL High (4 ~ 5V), Max source current = 10mA; CC: TTL Low (0 ~ 0.4V), Max sink current = 10mA
Dry contact; Open = OFF, Short = ON; Maximum voltage across Enable/Disable contacts = 6V
Selects Remote or Local operation by voltage: 0 ~ 0.6V = Local / 2 - 15V = Remote
Signals operating mode; Open collector: Local = Open (Max voltage = 30V), Remote = On (Max sink current = 10mA)
X
X
X
X
X
X
X
X
X
X
X
X
10. Enable/Disable
11. Remote/Local Selection
12. Remote/Local Signal
1.5 FRONT PANEL
1.Control Functions
X
X
X
X
X
X
X
X
X
X
Vout/ Iout manual adjust by separate encoders (COARSE and FINE adjustment selectable)
OVP/UVL manual adjust by VOLTAGE Adjust encoder, Front Panel Lock/Unlock
Address selection by VOLTAGE Adjust encoder. # of Addresses = 31
AC ON/OFF, Output On/Off, Restart Modes (Auto/Safe), Foldback Control (CV to CC), Go-to-Local
RS-232/RS-485, LAN, IEEE (IEMD) and USB selection by rear panel DIP-switch
Baud rate selection (RS-232/RS-485 only): 1200, 2400, 4800, 9600 and 19,200 (by Current Adjust encoder)
Advanced Parallel Master/Slave: Hx = Master unit, where x = # of Slave units (0 to 4); S = Slave unit(s)
Voltage: 4 digits, Accuracy: ± 0.5% of Vo(rated) ±1 count
2.Display
Current: 4 digits, Accuracy: ± 0.5% of Vo(rated) ±1 count
VOLTAGE meter displays voltage at power supply (Local sense) or at load (Remote sense)
3.Indications
Green LED’s: PREVIEW, FOLD, REM./LOCAL, OUT ON/OFF, CV/CC, FINE
Red LED:.ALARM (OVP, OTP, FOLD, AC FAIL, ENA, SO)
X
1.6 DIGITAL PROGRAMMING & READBACK
1. Vout Programming Accuracy
2. Iout Programming Accuracy
3. Vout Programming Resolution
4. Iout Programming Resolution
5. Vout Readback Accuracy
6. Iout Readback Accuracy
7. Vout Readback Resolution
8. Iout Readback Resolution
9. OV Response Time
± 0.5% of Vo(rated)
X
X
X
X
X
X
X
X
X
± 0.5% of Io(rated) for units with Io < 187.5A; ± 0.7% of Io(rated) for Io ≥187.5A
0.02% of Vo(rated)
0.04% of Io(rated)
± (0.1% of Vo(actual) + 0.2% of Vo(rated))
± (0.1% of Io(actual) + 0.4% of Io(rated))
0.02% of Vo(rated)
0.02% of Io(rated)
20ms maximum (between Vout exceeding IEEE Limit and supply Inhibit turning On)
Set OVP/UVL limits, Set Local/Remote, Operating parameters and Status, Get Identity
10. Other Functions
*1. Ripple and Noise at Vo(rated) and rated Load, Ta = 25C and nominal AC input, per EIJ R9002A.
*2. Time for the Output voltage to recover within 2% of rating for a load current change of 50~100% or 100-50% of rated Output.
*3. Operating with a load that continuously pulses the current (or voltage) can reduce the operating life of the Power Supply. Please contact TDK-Lambda Sales/Technical Support to discuss the
application in detail.
All specifications subject to change without notice.
5 GenesysTM 3U 10/15kW
5秒后页面跳转
STM32H743技术深度剖析与应用案例探索
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
74HC14芯片资料介绍：性能特性分析、引脚介绍
LM1875芯片手册：功放参数分析、引脚说明、电路设计要点
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
