Document 686
For Analog Devices ADM2482E and
ADM2487E RS-485 Transceivers
SMT Power Transformer
•ꢀDesigned specifically for use with Analog Devices ADM2482E
and ADM2487E High Speed, Isolated RS-485 Transceivers
with Integrated Transformer Driver
•ꢀCenter tapped primary and secondary
•ꢀ2500 Vrms primary to secondary isolation
Core material Ferrite
Terminations RoHS compliant tin-silver over tin over nickel over phos
bronze. Other terminations available at additional cost.
Weight 1.0 g
Ambient temperature –40°C to +85°C
Storage temperature Component: –40°C to +85°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 600 per 13″ reel; Plastic tape: 24 mm wide,
0.37 mm thick, 16 mm pocket spacing, 6.1 mm pocket depth
PCB washing Tested with pure water or alcohol only. For other solvents,
see Doc787_PCB_Washing.pdf
Leakage
inductance4
max (µH)
Volt-time
product5
(V-µsec)
DCR max (Ohms)3
Pri/sec
voltage
Inductance2
min (µH)
Power6 Turns ratio
Part number1
1/2 pri
1/2 sec
(W)
pri : sec
GA3157-AL_
5 V to 3.3 V
45.6
0.130
0.155
1.14
34.4
7.2
1 : 0.88
Dot indicates pin 1
1. When ordering, please specify termination and packaging codes:
0.067
1,70
0.358
9,09
GA3157-ALD
1
8
8
5
1
Termination: L = RoHS compliant tin-silver over tin over nickel over
phos bronze.
0.394
10,00
Special order: T = RoHS tin-silver-copper (95.5/4/0.5)
or S = non-RoHS tin-lead (63/37).
0.079
2,00
max
Packaging: D = 13″ machine ready reel. EIA-481 embossed plastic
4
tape (600 per full reel).
0.063
1,60
B = Less than full reel. In tape, but not machine ready.
To have a leader and trailer added ($25 charge), use
code letter D instead.
Recommended
Land Pattern
0.475
12,07
max
2. Inductance is tested between pins 4 and 3 at 500 kHz, 0.5 Vrms, 0 Adc.
3. DCR is for each half of the primary and secondary.
4. Leakage inductance is for the primary with both windings connected in
series and with the secondary windings shorted.
5. Based on Bsat of the core at 25°C and number of turns on winding 4-3.
6. Calculated output power based on 150 kHz operating frequency. Power
varies depending on application.
Parts manufactured prior
to December 2011 may be
marked differently.
0.235
5,97
max
0.004/0,10
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
0.063
1,60
4
8
L = 45.6 µH min
DCR = 0.155 Ohms max
DCR = 0.13 Ohms max
0.079
2,00
3
Primary
2
7
1
Secondary
6
L = 45.6 µH min
DCR = 0.13 Ohms max
inches
mm
DCR = 0.155 Ohms max
5
Dimensions are in
1
Primary windings and secondary windings
to be connected in series on the PC board.
Document 686 Revised 12/14/11
US +1-847-639-6400 sales@coilcraft.com
UK +44-1236-730595 sales@coilcraft-europe.com
Taiwan +886-2-2264 3646 sales@coilcraft.com.tw
China +86-21-6218 8074 sales@coilcraft.com.cn
Singapore + 65-6484 8412 sales@coilcraft.com.sg
© Coilcraft Inc. 2013
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.