FC1-XX-XX-XX-XX
REVISION AC
(No OF POS x .03937[1.0000])
+ .092 [2.34] REF
No OF POSITIONS
-05 THRU -25
(SEE NOTE 8 )
C
OPTIONS
-WT: WELD TAB (LEAD
STYLE -02 & -L2 ONLY)
-LC: LOCKING CLIP (SEE FIG 3)
(LEAD STYLE -01 & -L1 ONLY)
(SEE NOTE 9)
(No OF POS x .03937[1.0000])
+ .03937[1.0000] REF
DO NOT
SCALE FROM
THIS PRINT
LEAD STYLE
-01 VERTICAL (SEE FIG 2, C-136-01-X)
03
01
-02 HORIZONTAL (SEE FIG. 1) (C-136-02-X)
-K: POLYIMIDE FILM PAD
(LEAD STYLE -01 & -L1 ONLY)
(USE K-DOT-.157-.250-.005)
(SEE NOTE 7)
-L1 VERTICAL (LOW INSERTION FORCE) (C-136-03-X)
-L2 HORIZONTAL (LOW INSERTION FORCE) (C-136-04-X)
.109 2.77 REF
-TR: TAPE & REEL
PLATING
-T: MATTE TIN CONTACT AND TAIL
-TM: MATTE TIN CONTACT AND TAIL
02
{(NO OF POS - 1 ) x
.03937 [1.0000]} .002 [.05]
-01 / -L1 [VERTICAL LEAD STYLES]
"B"
RECOMMENDED CABLE WIDTH
{(NO. OF POSITIONS x .03937 [1.0000])
+ .040 [1.00] +/- .010 [.25] }
FC1-XX-S
WT-10-01-XX
.033 0.84 REF
"A" REF
C-136-02-XX
OR
C-136-04-XX
.132 3.35
REF
C
.203 5.16
.204±.003 5.182±0.08
.2450±.0030 6.223±0.076
'A'
C
.004[.10]
.060 1.524 REF
C-136-01-XX
OR
C-136-03-XX
01
"B"
.026 0.67
.065 1.638 REF
C
2
MAX SWAY
(TYP)
.004 [0.10]
.012 0.30 REF
(SEE NOTE 6)
FIG 2
SECTION "B"-"B"
-01 /-L1: VERTICAL
.03937 1.0000 (TO BE MEASURED AT THE TAIL TIP)
DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1
NOTES:
.001 0.03
C
1.
REPRESENTS A CRITICAL DIMENSION.
-02 / -L2 [HORIZONTAL LEAD STYLES]
FIG 1
2. NOTE DELETED
3. BURR ALLOWANCE: .0015[.038] MAX.
4. MAXIMUM CUT FLASH: .010 [.25].
5. MINIMUM PUSHOUT FORCE: .5 LB.
6. TAIL SWAY MUST BE IN SAME DIRECTION
ON ALL CONTACT TAILS.
DETAIL 'A'
SCALE 8 : 1
FIG 3
-LC OPTION
7. KAPTON PAD (-K) AVAILABLE ON ALL POSITIONS FOR LEAD STYLE
-01 & -L1 (SEE FIG. 4).
SAME AS FIG. 2 EXCEPT AS SHOWN
8. -05 THRU -10 POSITIONS ARE 2 PARTS PER AND REQUIRE MULTI-CUTTING.
9. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE –LC OPTION IS NOT
COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS MANUAL
PLACEMENT FOR ALL ASSEMBLIES WITH THE –LC OPTION.
PROPRIETARY NOTE
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DECIMALS
ANGLES
2
.XX: .01 [.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
.XXX: .005 [.13]
+.010
-.000
.XXXX: .0020 [.508]
.055
1.40+0.25
0.00
SHEET SCALE: 4:1
DO NOT SCALE DRAWING
DESCRIPTION:
1MM SOCKET
.010 0.25 REF
LC-06-TM
HOUSING: BLACK LCP
CONTACT: PHOSPHOR BRONZE
WELD TABS: BRASS
DWG. NO.
{(NO OF POS x .03937 [1.0000])
+ .059 [1.50]} .005 [.13]
FC1-XX-XX-XX-XX
G. PURVIS 3/1/1999
.056 1.42 REF
SHEET 1 OF 2
BY:
F:\DWG\MISC\MKTG\FC1-XX-XX-XX-XX-MKT.SLDDRW