SOLID TANTALUM ELECTROLYTIC CAPACITORS
Resin-molded Chip,
High Capacitance Series
F98
Specifications
Compliant to the RoHS directive (2002/95/EC).
Item
Performance Characteristics
Category
Temperature Range
--55 to +125°C (Rated temperature : 85°C)
Capacitance Tolerance ±20 (at 120Hz)
%
Dissipation Factor
ESR
Refer to the list below
Refer to the list below
Refer to next page
Provided that
After 5 minute's application of rated voltage, leakage current at 85°C,
10 times or less than 20°C specified value.
After 5 minute's application of rated voltage, leakage current at 125°C,
12.5 times or less than 20°C specified value.
Leakage Current
At 40°C, 90 to 95% R.H., For 500hours (No voltage applied)
Damp Heat
(Steady State)
Capacitance Change
Dissipation Factor
Leakage Current
Refer to the list below (* 1)
150% or less of initial specified value
200% or less of initial specified value
At --55°C / +125°C, For 30 minutes each, 5 cycles
Type numbering system (Example : 6.3V 10µF)
Capacitance Change
Dissipation Factor
Leakage Current
Refer to the list below (* 1)
150% or less than the initial specified value
Initial specified value or less
Temperature Cycles
1
2
3
4
5
6
7
8
9
10 11
Taping code
(Refer to page 321 for details)
F 9 8 0 J 1 0 6 M M
At 260°C, For 10 seconds, Reflow,
Case code
Resistance to Soldering
Heat
Capacitance Change
Leakage Current
Leakage Current
Refer to the list below (* 1)
Initial specified value or less
Initial specified value or less
Capacitance tolerance
Rated capacitance
Rated voltage
Series
After application of surge in series with a 1kΩ resistor at the
rate of 30 seconds ON, 30 seconds OFF, for 1000 successive
°C
test cycles at 85
, capacitors meet the characteristics
Drawing
Surge
requirements listed below.
Capacitance Change
Dissipation Factor
Refer to the list below (* 1)
L
W1
%
150 or less than the initial specified value
%
200 or less than the initial specified value
Leakage Current
H
After 1000 hours' application of rated voltage in series with a
3Ω resistor at 85°C, capacitors meet the characteristic
requirements listed below
Endurance
Shear Test
Capacitance Change
Dissipation Factor
Leakage Current
Refer to the list below (* 1)
150% or less than the initial specified value
200% or less than the initial specified value
W2
After applying the pressure load of 5N
for 10±1 seconds horizontally to the
center of capacitor side body which has
no electrode and has been soldered
beforehand on an aluminum substrate,
there shall be found neither exfoliation
nor its sign at the terminal electrode.
S1 S2 S1
(
mm)
•
5N (0.51kg f)
For 10 ± 1 seconds
Cace Code
W2
H
W1
S1
S2
L
U
M
S
1.10 ± 0.05 0.60 ± 0.05 0.35 ± 0.05 0.55 ± 0.05 0.3 ± 0.05 0.5
1.6 ± 0.1 0.85 ± 0.1 0.65 ± 0.1 0.8 ± 0.1 0.5 ± 0.1 0.6
2.0 ± 0.1 1.25 ± 0.1 0.9 ± 0.1 0.8 ± 0.1 0.5 ± 0.1 1.0
±
0.05
0.1
Keeping a capacitor surface-mounted on a substrate upside
down and supporting the substrate at both of the opposite
bottom points 45mm apart from the center of the capacitor, the
pressure strength is applied with
±
±
0.1
20
a specified jig at the center of the
substrate so that the substrate
may bend by 1mm as illustrated.
Then, there shall be found no
remarkable abnormality on the
capacitor terminals.
R230
Terminal Strength
Marking
45
45
Capacitance code
U Case
M Case
J
S Case
Js
As for the surge and derated voltage at 125 , refer to page 320 for details.
˚C
Rated
Capacitance
(µF)
Leakage
Current
A)
Disspation
Factor
*1
∆C/C
Case
code
ESR
Part Number
Rated Volt
Rated voltage
(Voltage code)
Rated voltage
(Voltage code)
(%)
(Ω@100kHz)
(
µ
(%@120Hz)
20
25
15
30
40
30
35
20
20
30
8
F980G475MUA
F980G106MUA
F980G226MMA
F980G336MMA
F980G476MMA
F980G686MSA
F980G107MSA
F980J475MUA
F980J475MMA
F980J106MUA
F980J106MMA
F980J226MMA
F980J336MMA
F980J476MMA
F980J476MSA
F981A225MUA
F981A225MMA
F981A475MMA
F981A106MMA
F981A226MSA
F981A336MSA
F981C105MMA
F981C225MMA
F981C475MMA
F981C106MSA
F981D105MMA
F981E105MMA
4.7
10
22
33
47
68
100
4.7
4.7
10
10
22
33
47
47
2.2
2.2
4.7
10
22
33
1
U
U
M
M
M
S
0.5
0.8
0.9
1.3
1.9
2.7
4.0
0.6
0.5
3.2
0.6
1.4
4.2
23.7
3.0
0.5
0.5
0.5
1.0
2.2
3.3
0.5
0.5
0.8
1.6
0.5
0.5
20
20
7.5
4
8
4
±30
±30
±30
±30
±30
±30
±30
±30
±30
±30
±30
±30
±30
±30
±30
±30
±30
±30
±30
±20
±30
±30
±30
±30
±20
±30
±30
4V
Standard Ratings
V
4
6.3
0J
10
1A
16
1C
20
1D
25
1E
Capacitance
code
Cap.(µF)
0G
Code
S
4
U
M
U
M
M
M
M
S
U
M
M
M
S
20
7.5
30
6
6
8
10
6
15
7.5
6
7.5
4
6
10
10
12
4
10
10
1
---
---
---
a
105
225
475
106
226
336
476
686
107
M
M
M
S
M
M
•
2.2
4.7
10
U
M
•
•
(U)
M
U
U
M
M
M
•
U
M
6.3V
20
35
45
25
15
6
•
M
M
U
•
22
(M)
S
J
M
M
•
33
S
n
47
s
M
S
68
(M)
S
S
w
A
6
10V
16V
20
20
30
6
•
(M)
100
(S)
( ) The series in parentheses are being developed.
Please contact to your local Nichicon sales office when
these series are being designed in your application.
S
M
M
M
S
M
M
2.2
4.7
10
1
6
12
18
6
20V
25V
1
8
1 : Leakage Current
˚C.
After 5 minute's application of rated voltage, leakage current at 20
*
CAT.8100Z
5秒后页面跳转
英伟达新AI芯片Rubin或提前半年亮相
苹果iPhone 17将全系采用三星/LG显示LTPO OLED面板
三星深化印度制造布局，供应链本地化进程加速
芯擎科技“星辰一号”自动驾驶芯片点亮成功，2025年量产在即
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
替代型号
如果您发现信息不准确，
