LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS
Standard snap-ins, 85℃
SMM
SMHSeries
Downsized
Longer life
Endurance with ripple current : 2,000 hours at 85
Non solvent resistant type
RoHS2 Compliant
・
・
・
℃
SMH
SPACIFICATIONS
◆
Items
Characteristics
Category
Temperature Range
-40 to +85
℃
Rated Voltage Range
Capacitance Tolerance
Leakage Current
6.3 to 100Vdc
20% (M)
(at 20 , 120Hz)
±
℃
I=0.02CV or 3mA, whichever is smaller.
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
(at 20 after 5 minutes)
℃
Dissipation Factor
Rated voltage (Vdc
)
6.3V 10V 16V 25V 35V 50V 63V 80V 100V
0.60 0.50 0.40 0.30 0.25 0.20 0.15 0.15 0.15
6.3V 10V 16V 25V 35V 50V 63V 80V 100V
(tan
)
δ
tan (Max.)
(at 20 , 120Hz)
δ
℃
Low Temperature
Characteristics
(Max. Impedance Ratio)
Rated voltage (Vdc
)
Z(-25 )/Z(+20
)
)
4
4
4
3
3
8
2
6
2
6
2
5
2
5
℃
℃
℃
Z(-40 )/Z(+20
15
15
15
10
(at 120Hz)
℃
Endurance
Shelf Life
The following specifications shall be satisfied when the capacitors are restored to 20 after subjected to DC voltage with the rated
℃
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 2,000 hours at 85
.
℃
Capacitance change
D.F. (tan
Leakage current
20% of the initial value
200% of the initial specified value
The initial specified value
≦±
≦
≦
)
δ
The following specifications shall be satisfied when the capacitors are restored to 20 after exposing them for 1,000 hours at 85 without
℃
℃
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change 20% of the initial value
D.F. (tan
≦±
)
150% of the initial specified value
The initial specified value
δ
≦
≦
Leakage current
DIMENSIONS [mm]
◆
●
●
Terminal Code : VS (φ22 toφ35) : Standard
Terminal Code : LI (φ35)
PC board pin-out
(View from Solder side)
PC board pin-out
(View from Solder side)
Sleeve (PET : Black)
Sleeve (PET : Black)
Negative mark
Negative mark
2-1.2×6
5±0.5
2-φ2
*
4.0±0.5
L±2
4.5±1
L±2
Vent
14.2±1
Vent
φD=35mm : 3.5±0.5mm
*
The standard design has no plastic disc.
PART NUMBERING SYSTEM
◆
1
2
3
4
5
6
7
8
9
10
11 12 13
14
15 16 17
18
E S M H A A A V S N A A A M A A A S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 820µF:821, 3,300µF:332)
Dummy terminal code
Terminal code
Voltage code (ex. 6.3V:6R3, 63V:630, 100V:101)
Series code
Category
Please refer to "Product code guide (snap-in type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1001Y 2024