SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS
Low ESR, 105℃
AIchipTM-MZJSeries
Lower ESR, 2,000 hours at 105
Rated voltage range : 6.3 to 35V
Nominal capacitance range : 10 to 1,800μF
Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
Vibration resistant structure
・
・
・
・
・
・
・
℃
MZJ
Lower ESR
MZA P4-16
RoHS2 Compliant
AEC-Q200 compliant : Please contact Chemi-Con for more details, test data, information.
SPECIFICATIONS
◆
Items
Characteristics
Category
Temperature Range
-55 to +105
℃
Rated Voltage Range 6.3 to 35Vdc
Capacitance Tolerance
Leakage Current
20% (M)
(at 20 , 120Hz)
℃
±
I=0.01CV or 3μA, whichever is greater.
Where, I : Max. leakage current (μA), C : Nominal capacitance (μF), V : Rated voltage (V)
(at 20 after 2 minutes)
℃
Dissipation Factor
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V
0.26 0.19 0.16 0.14 0.12
6.3V 10V 16V 25V 35V
(tan
)
δ
tan (Max.)
(at 20 , 120Hz)
δ
℃
Low Temperature
Characteristics
(Max. Impedance Ratio)
Rated voltage (Vdc)
Z(-25 )/Z(+20
)
℃
)
℃
)
℃
2
3
4
2
3
4
2
3
4
2
3
3
2
3
3
℃
Z(-40 )/Z(+20
℃
Z(-55 )/Z(+20
(at 120Hz)
℃
Endurance
The following specifications shall be satisfied when the capacitors are restored to 20 after the rated voltage is applied for 2,000 hours
℃
at 105
.
℃
Capacitance change
D.F. (tan
Leakage current
30% of the initial value
200% of the initial specified value
The initial specified value
≦±
≦
≦
)
δ
Shelf Life
The following specifications shall be satisfied when the capacitors are restored to 20 after exposing them for 1,000 hours at 105 without
℃ ℃
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change 30% of the initial value
D.F. (tan
≦±
)
200% of the initial specified value
The initial specified value
δ
≦
≦
Leakage current
Surge Voltage Test
The capacitors shall be subjected to 1,000 cycles each consisting of charging with the specified surge voltage for 30 5 seconds through
±
a protective resistor (as required for RC=0.1 0.05sec) and open-circuiting for 5.5 minutes at a room temperature of 15 to 35
.
℃
±
Rated voltage (Vdc
Surge voltage (Vdc
)
)
6.3V 10V 16V 25V 35V
7.2V 12V 18V 29V 40V
Appearance
No significant damage
Capacitance change
D.F. (tan
Leakage current
20% of the initial value
200% of the initial specified value
The initial specified value
≦±
≦
≦
)
δ
(Caution)
Surge Voltage Test intends to evaluate capacitors in durability of an exceptional excessive voltage under specific conditions.It does
not imply long-term use at all.
DIMENSIONS [mm]
● Terminal Code : A
◆
● Terminal Code : G(Vibration resistant structure)
● Size code : D61 to JA0
● Size code : HA0 and JA0
Size code
D
4
5
L
A
B
C
W
P
D61
E61
F61
F80
HA0
JA0
5.8 4.3 4.3 5.1 0.5 to 0.8 1.0
5.8 5.3 5.3 5.9 0.5 to 0.8 1.4
6.3 5.8 6.6 6.6 7.2 0.5 to 0.8 1.9
6.3 7.7 6.6 6.6 7.2 0.5 to 0.8 1.9
10.0 8.3 8.3 9.0 0.7 to 1.1 3.1
10 10.0 10.3 10.3 11.0 0.7 to 1.1 4.5
W
0.3max.
Vent for JA0
Vent for JA0
W
8
A±0.2
L±0.5
0.3max.
A±0.2
L±0.3 (Note)
Note : L±0.5 for HA0 and JA0
: Dummy terminals
MARKING
EX) 35V10µF
◆
● Rated voltage symbol
Rated voltage (Vdc)
Symbol
6.3
j
10
A
16
C
25
E
35
V
9j
10
VZJ
Applying voltage over the rated voltages causes the capacitors to have short lifetime.
Besides, applying voltage over the specified surge voltages may cause to have short circuit failure. A protection
circuit should be used if applied voltage will exceed the rated voltages.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1001R
4-14