SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS
Low ESR, 105℃
AIchipTM-MZJSeries
Lower ESR, 2,000 hours at 105
Rated voltage range : 6.3 to 35V
Nominal capacitance range : 10 to 1,800μF
Solvent resistant type (see PRECAUTIONS AND GUIDELINES)
Vibration resistant structure
・
・
・
・
・
・
℃
MZJ
Lower ESR
MZA P74
RoHS Compliant
SPECIFICATIONS
◆
Items
Characteristics
Category
Temperature Range
-
55 to +105℃
Rated Voltage Range 6.3 to 35Vdc
Capacitance Tolerance ±20% (M)
(at 20℃, 120Hz)
(at 20℃ after 2 minutes)
(at 20℃, 120Hz)
Leakage Current
I=0.01CV or 3µA, whichever is greater.
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
Dissipation Factor
(tanδ)
Rated voltage (Vdc)
tanδ(Max.)
6.3V
0.26
6.3V
2
3
4
10V
0.19
10V
2
3
4
16V
0.16
16V
2
3
4
25V
0.14
25V
2
3
3
35V
0.12
35V
2
3
3
Low Temperature
Characteristics
(Max. Impedance Ratio)
Rated voltage (Vdc)
Z(
Z(
Z(
-
-
-
25℃)/Z(+20℃)
40℃)/Z(+20℃)
55℃)/Z(+20℃)
(at 120Hz)
Endurance
Shelf Life
The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 2,000 hours
at 105℃.
Capacitance change
D.F. (tanδ)
Leakage current
≦±30% of the initial value
≦200% of the initial specified value
The initial specified value
≦
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 1,000 hours at 105℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change
≦±30% of the initial value
D.F. (tanδ)
Leakage current
≦
200% of the initial specified value
The initial specified value
≦
Surge Voltage Test The capacitors shall be subjected to 1,000 cycles each consisting of charging with the specified surge voltage for 30±5 seconds through
a protective resistor (as required for RC=0.1±0.05sec) and open-circuiting for 5.5 minutes at a room temperature of 15 to 35℃.
Rated voltage (Vdc)
Surge voltage (Vdc)
6.3V
7.2V
10V
12V
16V
18V
25V
29V
35V
40V
Appearance
No significant damage
Capacitance change
D.F. (tanδ)
Leakage current
≦±20% of the initial value
≦200% of the initial specified value
The initial specified value
≦
(Caution)
Surge Voltage Test intends to evaluate capacitors in durability of an exceptional excessive voltage under specific conditions.It does not
imply long-term use at all.
DIMENSIONS [mm]
● Terminal Code : A
◆
● Terminal Code : G(Vibration resistant structure)
● Size code : D61 to JA0
● Size code : HA0 and JA0
Size code
D
4
5
L
A
B
C
W
P
D61
E61
F61
F80
HA0
JA0
5.8 4.3 4.3 5.1 0.5 to 0.8 1.0
5.8 5.3 5.3 5.9 0.5 to 0.8 1.4
6.3 5.8 6.6 6.6 7.2 0.5 to 0.8 1.9
6.3 7.7 6.6 6.6 7.2 0.5 to 0.8 1.9
10.0 8.3 8.3 9.0 0.7 to 1.1 3.1
10 10.0 10.3 10.3 11.0 0.7 to 1.1 4.5
W
0.3max.
Vent for JA0
Vent for JA0
W
8
A±0.2
L±0.5
0.3max.
A±0.2
L±0.3 (Note)
Note : L±0.5 for HA0 and JA0
: Dummy terminals
MARKING
EX) 35V10µF
◆
● Rated voltage symbol
Rated voltage (Vdc)
Symbol
6.3
j
10
A
16
C
25
E
35
V
9j
10
VZJ
Applying voltage over the rated voltages causes the capacitors to have short lifetime.
Besides, applying voltage over the specified surge voltages may cause to have short circuit failure. A protection
circuit should be used if applied voltage will exceed the rated voltages.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1001N
72