SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS
High heat resistance, 125
C
MVH
@Lower ESR, Higher ripple current
@Endurance : 1,000 to 5,000 hours at 125C
@Suitable to fit for automotive equipment
@Solvent resistant type (10 to 50V)
@RoHS Compliant
125C
MVE
SPECIFICATIONS
?
Items
Characteristics
Category
Temperature Range
-40 to +125C
Rated Voltage Range 10 to 450Vdc
Capacitance Tolerance P20% (M)
(at 20C, 120Hz)
10 to 100Vdc
Leakage Current
Rated voltage (Vdc)
160 to 450Vdc
F60 to JA0
I=0.01CV or 3MA, whichever is greater.
I=0.03CV or 4MA, whichever is greater.
I=0.04CV+100
KE0 to MN0
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V)
Rated voltage (Vdc)
F60 to JA0
(at 20C after 2 minutes)
Dissipation Factor
10V 16V 25V 35V 50V 63V 80V 100V 160 to 250V 400 & 450V
0.24 0.20 0.16 0.14 0.14 0.12 0.12 0.10
0.22 0.18 0.16 0.14 0.12 0.14 0.10
When nominal capacitance exceeds 1,000MF, add 0.02 to the value above for each 1,000MF increase.
Rated voltage (Vdc)
10V 16V 25V 35V 50V 63V 80V 100V 160 to 250V 400 & 450V
(tane)
tanE (Max.)
0.20
0.24
KE0 to MN0
(at 20C, 120Hz)
Low Temperature
Characteristics
Z(
Z(
Z(
Z(
-25C)/Z(+20C)
-40C)/Z(+20C)
-25C)/Z(+20C)
-40C)/Z(+20C)
3
6
4
8
2
4
3
6
2
4
2
4
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
2
3
(Max. Impedance Ratio) F60 to JA0
3
6
6
KE0 to MN0
10
(at 120Hz)
Endurance
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for the specified
time at 125C.
F60 to H63 (10 to 100Vdc) : 1,000hours
HA0 to JA0 (10 to 100Vdc) : 2,000hours
Time
KE0 to MN0 (10 to 100Vdc) : 5,000hours
KE0 to MN0 (160 to 450Vdc) : 2,000hours
Capacitance change
D.F. (tanE)
[P30% of the initial value
[300% of the initial specified value
[The initial specified value
Leakage current
Shelf Life
The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 1,000 hours (500 hours
for 400 to 450Vdc) at 125C without voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage
according to Item 4.1 of JIS C 5101-4.
Rated voltage(Vdc)
Capacitance change
D.F. (tanE)
10 to 50Vdc
63 to 450Vdc
[P30% of the initial value
[P30% of the initial value
[300% of the initial specified value [300% of the initial specified value
Leakage current
[The initial specified value
[500% of the initial specified value
MARKING
?DIMENSIONS [mm]
@Terminal Code : A
@Size code : F60 to MN0
?
F60 to JA0
EX) 35V47MF
W
74H
47
35V
Size code
F60
F80
D
L
A
B
C
W
P
6.3 5.7 6.6 6.6 7.2 0.5 to 0.8 1.9
6.3 7.7 6.6 6.6 7.2 0.5 to 0.8 1.9
H63
HA0
JA0
KE0
KG5
LH0
LN0
MH0
MN0
8
8
6.3 8.3 8.3 9.0 0.5 to 0.8 2.3
10.0 8.3 8.3 9.0 0.7 to 1.1 3.1
0.3max.
AP0.2
LP0.5 (Note)
Note : LP0.3 for F60 and F80
KE0 to MN0
10 10.0 10.3 10.3 11.0 0.7 to 1.1 4.5
12.5 13.5 13.0 13.0 13.7 1.0 to 1.3 4.2
12.5 16.0 13.0 13.0 13.7 1.0 to 1.3 4.2
16 16.5 17.0 17.0 18.0 1.0 to 1.3 6.5
16 21.5 17.0 17.0 18.0 1.0 to 1.3 6.5
18 16.5 19.0 19.0 20.0 1.0 to 1.3 6.5
18 21.5 19.0 19.0 20.0 1.0 to 1.3 6.5
EX) 16V1,000MF
0V
MVH
@Terminal Code : G
@Size code : LH0 to MN0
1000
16V
W
0.3max.
AP0.2
LP0.5
: Dummy terminals
(1/2)
CAT. No. E1001K