LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS
LXG
Long life snap-ins, 105
C
@Endurance with ripple current : 105C 5000 hours
@Non solvent-proof type
@Pb-free design
longer life
KMH
SPECIFICATIONS
?
Items
Characteristics
Category
Temperature Range
-40 to +105C
(at 20C, 120Hz)
Rated Voltage Range 10 to 100Vdc
Capacitance Tolerance P20% (M)
Leakage Current
I=0.02CV or 3mA, whichever is smaller.
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V)
(at 20C after 5 minutes)
(at 20C, 120Hz)
10V 16V 25V 35V 50V 63V 80 & 100V
0.60 0.45 0.30 0.25 0.20 0.15 0.15
Dissipation Factor
(tane)
Rated voltage (Vdc)
tanE (Max.)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Capacitance change : Capacitance at the lowest operating temperature shall not be less than 70% of the 20C value.
Rated voltage (Vdc)
10V 16V 25V 35V 50V 63V 80 & 100V
Z(-25C)/Z(+20C)
4
4
3
3
8
2
6
2
6
2
5
(at 120Hz)
Z(-40C)/Z(+20C)
15
15
10
Endurance
Shelf Life
The following specifications shall be satisfied when the capacitors are restored to 20C after subjected to DC voltage with rated ripple
current is applied for 5000 hours at 105C.
Capacitance change
D.F. (tanE)
[P25% of the initial value
[250% of the initial specified value
[The initial specified value
Leakage current
The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 500 hours at 105C
without voltage applied.
Capacitance change
D.F. (tanE)
[P20% of the initial value
[150% of the initial specified value
[The initial specified value
Leakage current
DIMENSIONS [mm]
?
@Terminal Code : VS (F22 to F35) : Standard
@Terminal Code : LI (F35)
PC board pin-out
-1.2B6
Sleeve (PET)
Negative mark
Negative mark
Sleeve (PET)
PC board pin-out
2
5P0.5
2-F2
*
14.2P1
4.0P0.5
LP2
LP2
4.5P1
Vent
Vent
* D=35mm : 3.5 0.5mm
F
P
No plastic disk is the standard design
PART NUMBERING SYSTEM
?
1
2
3
4
5
6
7
8
9
10
11 12 13
14
15 16 17
18
E L X G A A A V S N A A A M A A A S
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 390MF:391,3300MF:332)
Dummy terminal code
Terminal code (VS, LI)
Voltage code (ex. 10V:100,100V:101)
Series code
Category
Please refer to "A guide to global code (snap-in type)"
RATED RIPPLE CURRENT MULTIPLIERS
?
@Frequency Multipliers
Frequency (Hz)
10 to 50Vdc
50
120
1.00
1.00
300
1.03
1.07
1k
10k
1.08
1.19
50k
1.08
1.20
0.95
0.92
1.05
1.13
63 to 100Vdc
(1/3)
CAT. No. E1001E