MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS
Standard, Downsized, 105℃
KMQ P122
Downsized
KMGSeries
Endurance with ripple current : 1,000 to 2,000 hours at 105
Solvent resistant type except 350 to 450Vdc
(see PRECAUTIONS AND GUIDELINES)
RoHS Compliant
・
・
℃
KMG
・
SPECIFICATIONS
◆
Items
Characteristics
Category
Temperature Range
-
55 to +105℃(6.3 to 100Vdc)
-40 to +105℃(160 to 400Vdc) -25 to +105℃(450Vdc)
Rated Voltage Range 6.3 to 450Vdc
Capacitance Tolerance ±20% (M)
(at 20℃, 120Hz)
Leakage Current
6.3 to 100Vdc
I=0.03CV or 4µA, whichever is greater.
160 to 450Vdc
Time
After 1minute
After 5minutes
CV
CV≦1,000 I=0.1CV+40 max.
CV 1,000 I=0.04CV+100 max.
I=0.03CV+15 max.
I=0.02CV+25 max.
>
(at 20℃ after 1 minute)
(at 20℃)
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
Dissipation Factor
(tanδ)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V 63V 100V 160 to 250V 350 to 400V 450V
tanδ(Max.)
0.34 0.24 0.20 0.16 0.14 0.12 0.10 0.08
0.20
0.24
0.24
When nominal capacitance exceeds 1,000µF, add 0.02 to the value above for each 1,000µF increase.
(at 20℃, 120Hz)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V 63V 100V 160 to 250V 350 to 400V 450V
Z(-
25℃)/Z(+20℃)
40℃)/Z(+20℃)
5
4
3
8
2
5
2
4
2
3
2
3
2
3
3
4
6
6
6
Z(
-
(at 120Hz)
12
10
Endurance
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 1,000 hours (2,000 hours to meet the following two conditions
1): 160Vdc and larger, 2) :φ12.5 and larger) at 105℃.
Capacitance change
D.F. (tanδ)
Leakage current
≦±20% of the initial value
≦200% of the initial specified value
≦The initial specified value
Shelf Life
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 1,000 hours at 105℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Rated voltage
6.3 to 100Vcd
160 to 450Vdc
Capacitance change
D.F. (tanδ)
Leakage current
≦±20% of the initial value
≦200% of the initial specified value
≦The initial specified value
≦±20% of the initial value
≦200% of the initial specified value
≦500% of the initial specified value
DIMENSIONS [mm]
●Terminal Code : E
◆
Sleeve (PET : Brown)
φD
5
6.3
8
10 12.5 16
18
φd 0.5 0.5 0.6 0.6 0.6 0.8 0.8
F
φD'
L'
2.0 2.5 3.5 5.0 5.0 7.5 7.5
φD+0.5max
L+1.5max
L'
15min.
4min.
(φ5 toφ10)
(φ12.5 toφ18)
Vent
Gas escape end seal
(exceptφ5)
PART NUMBERING SYSTEM
◆
1
2
3
4
5
6
7
8
9
10
11 12 13
14
15 16 17
18
E K MG A A A E A A A A A M A A A N
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 1.0µF:1R0,10µF:100,100µF:101)
Lead forming·taping code
Terminal code
Voltage code (ex. 6.3V:6R3,35V:350,100V:101)
Series code
Category
Please refer to "Product code guide (radial lead type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1001N
129