REVISION R
EEDP-XXX-XX.XX-XXX-XXX-X
THIS PRODUCT MANUFACTURED
WITH LEAD-FREE PROCESSING
WIRING OPTION
Pb
-1: PIN 1 TO PIN 1
No OF PAIRS
DO NOT
SCALE FROM
THIS PRINT
-2: PIN 1 TO PIN 2
-008, -016, -024 (SEE SHEET 5), -032
-3: PIN 1 TO PIN N-1
-4: PIN 1 TO PIN N
(SEE TABLE 8, SHEET 8)
SUB-PCB-0453-EEDP-XXX-EC-S
(SEE NOTE 7)
(SEE TABLE 3, SHEET 5 FOR
-008, -016, -032; SEE
TABLE 5, SHEET 6 FOR -024)
LENGTH: XX.XX + .734[18.64] REF
LENGTH
-XX.XX (INCHES)
(03.75[95.3] MIN)
(SEE NOTE 2)
N
LENGTH: XX.XX 01%
(CABLE LENGTH)
(SEE TABLE 2)
SECOND END
'A'
(SEE NOTE 10)
02
-DV1: DOUBLE VERTICAL
-DV2: DOUBLE VERTICAL (FLIPPED)
-DS1: DV1 WITH CAPTIVE PANEL SCREWS
-DS2: DV2 WITH CAPTIVE PANEL SCREWS
-RA1: RIGHT ANGLE (SHROUD UP)
-RA2: RIGHT ANGLE (SHROUD DOWN)
-RS1: RA1 WITH CAPTIVE PANEL SCREWS
-RS2: RA2 WITH CAPTIVE PANEL SCREWS
-LV1: DV1 WITH LATCHES (SEE SHEET 7)
-LV2: DV2 WITH LATCHES (SEE SHEET 7)
-RL1: RIGHT ANGLE W/ LATCHES (SHROUD UP)
-RL2: RIGHT ANGLE W/ LATCHES (SHROUD DOWN)
FIRST END
-DV1: DOUBLE VERTICAL
-DV2: DOUBLE VERTICAL (FLIPPED)
-DS1: DV1 WITH CAPTIVE PANEL SCREWS
-DS2: DV2 WITH CAPTIVE PANEL SCREWS
-RA1: RIGHT ANGLE (SHROUD UP)
-RA2: RIGHT ANGLE (SHROUD DOWN)
-RS1: RA1 WITH CAPTIVE PANEL SCREWS
"A"
REF
"B"
REF
"C"
REF
C
L
-RS2: RA2 WITH CAPTIVE PANEL SCREWS
-LV1: DV1 WITH LATCHES (SEE SHEET 7)
-LV2: DV2 WITH LATCHES (SEE SHEET 7)
(SEE SHEET 3 & 4 AND TABLE 9, SHEET 8)
-RL1: RIGHT ANGLE W/ LATCHES (SHROUD UP)
-RL2: RIGHT ANGLE W/ LATCHES (SHROUD DOWN)
R
(SEE SHEET 2 &3 AND TABLE 9, SHEET 8)
R
LENGTH REF
HDRL-11
(SEE NOTE 5)
N
02
FIRST END
(SEE TABLE 2)
SECOND END
.647 16.43 REF
EDP-XX-01-SRD (TYP)
SUB-TTF-30100-XX-01-XX.XX (TYP)
.252 6.40 REF (TYP)
FIG 1
.062 1.57
REF
EEDP-016-XX.XX-3-DV1-RA1 SHOWN
EDP-XX-01
.540 13.72
REF (TYP)
DETAIL 'A'
NOTES:
N-1
(SEE TABLE 2)
01
.345 8.76 REF
SCALE 2.5 : 1
1.
REPRESENTS A CRITICAL DIMENSION.
2. SUB-TTF LENGTH IS EQUAL TO EEDP LENGTH.
3. ALL ASSEMBLIES TO BE 100% ELECTRICALLY TESTED
FOR SHORTS AND OPENS.
.157 4.00 REF
(SEE NOTE 8)
4. ALL ASSEMBLIES TO BE 100% HI-POT TESTED AT 300V.
5. TOP SUB-TTS NOT SHOWN IN THIS VIEW FOR CLARITY; HDRL-11
TO BE CENTERED ON LOWER SUB-TTS AS SHOWN; HDRL-11 IS
TO CONTAIN PART NUMBER, SHOP NUMBER, & DATE CODE.
6. FOR PACKAGING REQUIREMENTS REFERENCE PACKAGING
STANDARDS.
'B'
(SEE SHEET 8)
7. FOR PRE-TINNING PROCESSING INFORMATION ON THE SUB-PCB'S,
SEE TRAVELER SUB-PCB-0453-EEDP-"XXX".
8. KEY CONSUMES FOUR PITCHES.
9. LVX OPTION: TIGHTEN TO 1.4-1.5 IN-LBS.
10. CABLE LENGTHS LONGER THAN 40.00 INCHES ARE NOT SUPPORTED
BY S.I. TEST DATA.
01
N-1
(SEE TABLE 2)
STS-01
(TIGHTEN TO 1.4 - 1.7 IN-LBS)
(TYP)
TOLERANCES DO NOT APPLY
TO REFERENCE DIMENSIONS.
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
ANGLES
2
520 PARK EAST BLVD, NEW ALBANY, IN 47150
.XX: .01[.3]
PHONE: 812-944-6733
FAX: 812-948-5047
code 55322
.XXX: .005[.13]
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
e-Mail info@SAMTEC.com
.XXXX: .0020[.051]
SHEET SCALE: 1.25:1
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
TWIN-AX EDGE CARD CABLE ASSEMBLY
DWG. NO.
EEDP-XXX-XX.XX-XXX-XXX-X
BY:
BRATCHER 09/25/2003 SHEET 1 OF 9
F:\DWG\MISC\MKTG\EEDP-XXX-XX.XX-XXX-XXX-X-MKT.SLDDRW