EPhEoto-mSicXros3en0s9or6(T-rWansm1i1ss/iv4e)096-W11
Be sure to read Precautions on page 24.
■ Dimensions
Note: All units are in millimeters unless otherwise indicated.
■ Features
• Light-receiving element and amplification circuits contained in one
chip.
25 0.2
Two, R1
• Can use a power supply voltage of 4.5 to 16 V.
• Connects directly to C-MOS or TTL.
• Dark-ON Sensor: EE-SX3096-W11
• Light-ON Sensor: EE-SX4096-W11
• Pre-wired Sensors (AWG28).
19 0.15
Optical axis
6
0.2 5 0.2
Two, C2
Two, 3.2 0.2 dia. holes
Four, C0.3
12.6 0.2
3.4 0.2
Detector
• Solder-less lead wire connection to increase reliability.
• With a horizontal aperture.
Emitter
2.1 0.15
B
A
Sensing
Optical axis
2.1 0.15
window
■ Absolute Maximum Ratings (Ta = 25°C)
10 0.2
0.5 0.1
0.5 0.1
7.2 0.2
3.1
Item
Symbol
IF
Rated value
2.5 0.1
Emitter
Forward current
50 mA
(see note 1)
610MIN
O
V
G
K
A
4
Reverse voltage
VR
4 V
Four, Wires UL1061,
AWG#28
3.55
Cross section A-A
Cross section B-B
11.6 0.2
Detector
Power supply volt- VCC
age
16 V
B
A
Internal Circuit
Output voltage
Output current
VOUT
IOUT
28 V
A
G
16 mA
Permissible output POUT
250 mW
(see note 1)
O
Unless otherwise specified, the
tolerances are as shown below.
dissipation
K
V
Ambient tem- Operating
Topr
Tstg
–25°C to 75°C
–25°C to 85°C
perature
Dimensions
3 mm max.
Tolerance
0.3
Terminal No.
Name
Anode
Cathode
Storage
A
K
Note: 1. Refer to the temperature rating chart if the ambient temper-
ature exceeds 25°C.
3 < mm ≤ 6
0.375
0.45
V
Power supply
(Vcc)
2. If you mount the Sensor with screws, use M3 screws, spring
washers, and flat washers and use a tightening torque of 0.5
N·m max.
6 < mm ≤ 10
10 < mm ≤ 18
0.55
O
G
Output (OUT)
Ground (GND)
3. You should use the product in the condition without any
18 < mm ≤ 30
0.65
stress on the cable.
■ Electrical and Optical Characteristics (Ta = 25°C)
Item
Symbol
VF
Value
1.2 V typ., 1.5 V max.
0.01 μA typ., 10 μA max.
940 nm
Condition
Emitter
Forward voltage
Reverse current
IF = 20 mA
VR = 4 V
IR
Peak emission wave-
length
λP
IF = 20 mA
Detector
Low-level output volt- VOL
0.12 V typ., 0.4 V max.
15 V min.
VCC = 4.5 to 16 V, IOL = 16 mA, IF = 0 mA (EE-SX3096),
IF = 5 mA (EE-SX4096)
age
High-level output volt- VOH
age
VCC = 16 V, RL = 1 kΩ, IF = 5 mA (EE-SX3096),
IF = 0 mA (EE-SX4096)
Current consumption
ICC
3.2 mA typ., 10 mA max.
870 nm
VCC = 16 V
Peak spectral sensitivi- λP
ty wavelength
VCC = 4.5 to 16 V
LED current when output is OFF
LED current when output is ON
Hysteresis
IFT
2 mA typ., 5 mA max.
VCC = 4.5 to 16 V
ΔH
15% typ.
3kHz min.
3 μs typ.
20 μs typ.
VCC = 4.5 to 16 V (see note 1)
Response frequency
f
VCC = 4.5 to 16 V, IF = 15 mA, IOL = 16 mA (see note 2)
Response delay time
Response delay time
tPLH (tPHL
)
)
VCC = 4.5 to 16 V, IF = 15 mA, IOL = 16 mA (see note 3)
VCC = 4.5 to 16 V, IF = 15 mA, IOL = 16 mA (see note 3)
tPHL (tPLH
148
EE-SX3096-W11/4096-W11 Photomicrosensor (Transmissive)